Safety & Warnings
- Do not share the same power supply with other high-power appliances.
- Do not use in conjunction with any extension cords.
- Use the unit only as described in this guide.
- Do not immerse the unit, its power cord or any accessories in water or other liquid.
- Place the mop pad on the bottom of the mop head before use. The mop pad is used to wipe the floor and also to protect the floor. The mop pad can be washed and reused.
- When finished cleaning, turn the steam off to prevent damage to the floor.
- Do not use any detergent or chemicals in the tank.
- When adding water, you must turn off the power switch and unplug the unit first.
- Do not place the power cord close to any hot surfaces.
- Do not touch the nozzle part while the unit is in use.
- Do not spray steam onto devices that contain electrical components.
- Do not allow children or anyone unfamiliar with the method of use to use the unit.
- The maximum amount of water added to the appliance is 250ml. When adding water, pay attention to the cover buckle and avoid spills.
- Do not attempt to repair the product yourself. If it experiences any fault or damage, stop using it immediately and contact Kogan.com.
- Unplug the unit before cleaning.
Overview
Installation
![]() |
1a) Jet Nozzle Installation Align the jet nozzle with the air outlet head at the front of the main unit, then rotate it until the jet nozzle is firmly attached to the unit. |
![]() |
1b) Nylon Brush Installation Attach the small brush on the jet nozzle, ensuring the brush is installed as illustrated to the left. Otherwise, the installed brush will not work properly. |
![]() |
1c) Wiper Installation Attach the wiper to the jet nozzle. |
- Plug the unit into power and the power indicator will flash as the unit heats up.
- When the indicator stops flashing and turns solid (after about 20 seconds), the unit has finished heating and you can press the steam switch button. To stop the steam, press the switch button again.
- Use the controls to adjust the steam strength as required.
Note: Ensure the steam is directed away from pets, plants or other electrical appliances.
Extension Pole Installation
Align the extension pole with the main body of the unit and then attach it by gently rotating the extension pole into the main unit.
In the same way, the mop head can be connected to the extension pole and the extension pole can be connected to the Jet Nozzle.
Water Shortage
It is necessary to pay attention to the amount of water in the tank when you use the steamer. If the water level is too low, no water will be transferred. If the water tank is empty, severe damage can be caused to the unit.
Instructions
Removing and Filling the Water Tank
Note: Make sure that the unit is unplugged before putting the water in the tank.
![]() |
1. Press the water tank button and remove the water tank. |
![]() |
2. Pull the tank cover up and remove the tank lid. |
![]() |
3. Add water to the tank. Note: To extend the life of the unit, distilled water is recommended. Do not add any chemicals or detergent to the water tank. |
![]() |
4. Replace the water tank cover. |
![]() |
5. Press the water tank button and insert the water tank into the main unit. |
Cleaning & Care
Mop Pad Cleaning
- Clean regularly to avoid the spread of dirt and bacteria.
- When changing the mop pad, be careful not to touch the unit outlet with your hands to avoid burns.
- To remove odour from mop pad, dissolve 2 tablespoons each of baking soda and salt into a half a litre of water and let the mop stand in it for half a day. Half a cup of vinegar can be used instead.
- The mop pad is machine washable and should only be air-dried.
Note: When removing or replacing any accessories, ensure that the unit is unplugged and no steam is being emitted. The unit needs to be cooled for 15 minutes to prevent burns.
Main Unit
Wipe with a cloth which is dry or dampened with warm water and a touch of mild detergent. Do not immerse the unit in water or other liquids.
Storage
Unplug the power cord, allow the unit to cool down and wipe it clean. Remove the mop, wrap the power cord around the mop and store it in a dry and ventilated place.
Specifications
Rated Voltage |
240V |
Rated Power |
1200W |
Rated Frequency |
60Hz |
Maximum Amount of Water |
250ml |
Continuous Operation |
10-25min |
Troubleshooting
Issue |
Solution |
Unit not heating |
Ensure the power switch is on and there is power from the outlet |
The unit does not emit steam |
Check the water level in the water tank, add more if needed |
Unit spills water |
The steam direction is not set properly, use the controls to adjust the steam direction and strength |