Configuration
Power On the Device And Set The Direction
- Connect the power adaptor with a wall outlet, then connect the power cable to the device.
- Check the chain position:
- Left direction: Facing blinds, chain/rope on the left hand.
- Right direction: Facing blinds, chain/rope on the right hand.
- By default, the device is in the right direction. If your blinds are in the left direction, slide the switch on the bottom of the device to the left with the supplied pin. Be careful during this step, as the switch is fragile.
After connection with the app is complete, you can change device motor direction by selecting ‘Motor direction’ from the ‘More’ submenu.
Note:
Please be careful with the switch as it can break easily. Do not force it.
Installation
Installing The Mounting Bracket
Pull down on the blind adjustment chain, ensuring it is taut and without slack. Hang the supplied installation card on the bottom of the chain, keeping the chain held tight. According to the chain position, mark the two “L” or “R” holes on your wall.
Installation Mode 1 - Permanent
For permanent installation, mark the two holes for either “L” or “R” installation with the card. Replace the card with the mounting bracket and screw into place. The mounting bracket can be installed this way either by its side or flat.
Installation Mode 2 (No Holes, Removable)
For a removable installation, use the supplied 3M adhesive to fix to a wall. It is recommended to leave the mounting bracket to set on the wall for at least 12 hours before applying the full weight of the attached device.
Fitting The Blind Adjustment Chain To The Device
Open the device backing by pushing gently inwards to release.
Determine the suitable gear from the below diagram and attach this to the device.
Fix the blind adjustment chain to the gear and close the device backing.
![]() |
![]() |
![]() |
|||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
2mm | 4mm | 6mm | 4.5x6mm | 4.5x12mm | metal chain | beaded chain | 3.2mm |
Please note that if the incorrect gear is selected, the chain will be noisy during operation.
Note:
This device is suited only for blinds with a looped adjustment chain and not suited for blinds with free-hanging cords or an adjustment wand/rod.
Attaching The Device To A Mounting Bracket
Once the mountain bracket is installed, simply attach the device to the bracket via the two grooves on the rear of the device and slide down until it locks into place. Ensure the chain is reasonably tight, with no slack.
![]() |
![]() |
Slide down until it locks into place, ensure the chain is taut. | Release Button |
To remove the device from the mountain bracket, simply press in on the Release Button
Top up the projection on the bottom, slide upon groove, open up the backboard and take out the chain.
Setting Up
Set device limits
![]() |
![]() |
|
1. Push the Up Arrow (left button) until the shades open all the way. | 2. Reach high limit position, push the Stop Button. | |
![]() |
![]() |
![]() |
3. Push and hold the Stop Button until the red light flashes (about 5 seconds). | 4. Once the red light flashes push the Down Arrow until the shades close. | 5. Hit the Stop Button when they are completely closed. The device will wait few seconds and then flash. |
Pairing with the remote
The device not only pairs with the mobile, but also with the remote.
![]() |
||
Push and hold Stop (middle button) until the red light flashes (about 5 seconds). |
Once it's starts flashing, push either the up or down button on the remote. | Pairing is successful when up and down lights on the blind motor are flashing. |
A holder for the remote control is included, which can be secured to the wall if desired.
Factory Reset
To reset the device, push the Up Arrow (left button) & Down Arrow (right button) for about 8 seconds until it flashes the lights.
Connect to SmarterHome™ App
Install App
Download the “Kogan SmarterHome™” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification code sent by SMS.
To register:
1. Tap to enter registration page.
2. The system automatically recognises your country/area. You can also select your country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by mobile number’ and enter the verification code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
5. Once registered, tap “+” in the upper right corner of the app’s home page to add a new device through the network.
Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode (the Up arrow will be continuously flashing). If not, you can manually set the device in pairing mode via the following step:
Hold the Up Arrow (left button) and Stop Button (middle button) simultaneously until the up Arrow begins flashing in blue.
Add The Device Through The Network
1. Ensure that the device is in pairing mode, with the indicator light rapidly flashing and tap “Confirm light is rapidly flashing”.
2. Select Wi-Fi network (note: network must be 2.4GHz band) and enter the password. The device will commence the pairing process and connect to the app.
3. After successfully adding the device, it will be shown on the home page. Tap to enter its control page.
Using SmarterHome™ App
The connection is now complete and you can tap on the ‘open’ or ‘closed’ blind icons to trigger the function directly via the app.
To access device functions, tap on the device from the app’s home page (Control Panel) and select “More”
Schedule
Use the scheduling function to set the blinds to open or close at set times of the day. Times will have a variance factor of +/- 30 seconds.
Google Home Control
Note: You will need to have set up a Google Home account prior to linking your Kogan SmarterHome™ device.
- Select “Menu” and then “Home Control”.
- In the “Home Control” screen, select the “+” icon in the bottom right.
- A list will appear showing actions and a search function to access more apps from here, install the SmarterHome™ app.
![]() |
![]() |
![]() |
Login to App |
Add Device |
Select Device |
- Log into your SmarterHome™ account with your email address or mobile number.
- Once linked, it will show the devices linked to your account, you can assign them to rooms. You will be prompted to authorise apps to sync.
- Click “Done” and then it will give you a list of commands available.
- When successfully linked, you will see it on your “Home Control” screen at the bottom of the app screen. You can now control your Kogan SmarterHome™ devices through Google Home.
![]() |
![]() |
Assign Room |
Update Home Control |
Try saying “Hey Google, close the blinds,” or “Hey Google, open the blinds to 40%”
Alexa
Note: You will need to have set up an Alexa account prior to linking your Kogan SmarterHome™ device.
- Select “Menu” and then “Skills”.
- Search for the app and enable it.
- Login to your SmarterHome™ account with your email address or mobile number.
- Select “Discover Devices” and the app will begin searching.
When successfully linked, you will see a list of connected Kogan SmarterHome™ devices. You can now control your Kogan SmarterHome™ devices through Alexa with your voice.
![]() |
![]() |
![]() |
Alexa Account Setup |
Search App in All Skills |
Enable App |
![]() |
![]() |
![]() |
Login to App |
Discover Devices |
Setup Device |
Try saying “Alexa, close the blinds,” or “Alexa, open the blinds to 40%”
Specifications
Control method |
Mobile or Remote |
Torque |
1.35N.m |
Speed |
55rpm |
Adapter voltage |
110V-240V |
Frequency |
2.4GHz |
Voltage |
12V |
Rated current |
1.2A |
Maximum blinds size |
2.5m x 3.5m |
Maximum weight |
10kg |