Safety & Warnings
Read all instructions carefully before using the device.
- Unplug the monitor before cleaning it with a slightly damp, clean cloth.
- Wiping the screen once it has been turned off with a dry microfibre cloth is recommended.
- Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
- This monitor is designed with ventilation holes on the back of the casing. Do not cover or block them.
- Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking adequate ventilation.
- Do not insert any objects or spray any liquids into the vents.
- Do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may injure nearby people.
- Unplug the monitor if it is not going to be used for an extended period.
- Do not place heavy objects on the monitor, its power cord or any connected cables.
- Do not open the back panel of the monitor, as it contains a high-voltage current even when not plugged in.
Components
| A | Monitor | E |
Stand screws (x 4) |
| B |
Stand stem |
F | Audio cable |
| C | Stand base | G | DP cable |
| D |
Power cord |
H | Quick Start Guide |
Overview
Monitor Controls
1. 
Power Button: Press to turn the monitor on/off.
2. 
Exit Button: Press to exit.
3. 
Up Button: Press to move up in the menus.
4. 
Down Button: Press to move down in the menus.
5. 
Menu Button: Press to display the OSD menu or enter sub-menus.
Monitor Ports
6. Audio Output: Insert one end of the audio cable into the computers audio output to receive the audio signals from your monitor.
7. DP Connector: Insert one end of the DP cable into the computer’s DP output and connect the other end to the monitor’s DP port.
8. HDMI Connector: Insert one end of the HDMI cable into the computer’s HDMI output and connect the other end to the monitor’s HDMI port.
9. USB Connector: Insert one end of the USB cable into the Monitor’s USB output and connect a device. The port has a 5V/0.5A power supply, and can also be used to Update Software.
10. Power Connector: Insert the power cable to supply power to the monitor.
Stand Assembly
1. Pick out the monitor from Carton Box carefully.
2. Take out the Leg and Support column, connect the two parts.
3. Take out the connection block by pressing the detach button (keep the monitor in its protective foam).
4. Insert the Connection Block into the back cabinet and then push down the stand until firmly connected.
5. Lift monitor up straightly and remove the bottom foam.
6. Stand Leg installation is done.
7. Complete overall assembly.
Note 1: To prevent pinching, please do not place your hand within the gap between the stand and the monitor.
Note 2: To prevent falling, please avoid holding monitor by the base or inverting the monitor.
Note: Do not invert the machine to prevent falling.
Note: To avoid damage, do not touch the screen when moving the monitor.
Wall Mounting
 |
VESA 100 x 100mm Wall mount Note: VESA mount or mounting accessory are excluded. |
1. Open the box, take out the product with protection form attached and gently place it on a desktop or table. Remove the extra parts and the foam covering the back of the monitor. Press the release button to remove the stand plate. If the monitor was already attached to the stand, remove the stand.
2. Remove the original screws x4 
from the opening in the back of the monitor.
3. Follow the directions with your mount, stand, or accessory and install the monitor on the wall or fixture as desired. Remember to use the included 4 screws when mounting the monitor. Refer to the image 
for correct screw placement.
Note: Do not discard the original screws. These may be needed in the future.
Connectivity
Power Cable
Connect the included power cable to the power connector, and then plug the other end into a wall outlet.
Earphones
Plug in your earphones to receive audio signals from your monitor. If your earphones are connected to the monitor and audio devices are connected to your computer at the same time, the audio devices will not produce sound. Earphones and other audio devices are not included.
USB
In order for the monitor to receive USB signals from the computer, use a USB cable
to connect the monitor to the computer.
HDMI
In order for the monitor to receive HDMI signals from the computer, use the HDMI cable to connect the monitor to the computer.
Note: To use the highest refresh rate and resolution your monitor supports, an HDMI 2.0 cable must be used via HDMI Port 1, or a Displayport cable with the DP port.
DP
In order for the monitor to receive DP signals from the computer, use the DP cable to connect the monitor to the computer.
Basic Operation
Note: Insert one end of the DP cable into your PC’s graphics card. An HDMI cable may also be used. An HDMI cable is not included. To use the highest refresh rate and resolution your monitor supports, an HDMI 2.0 cable must be used via HDMI Port 1, or a Displayport cable with the DP port.
1. Connect the other end of the cable to the corresponding connector on your monitor.
2. Connect the power cable to your monitor then connect the other end to your power source. It is recommended that you use a surge protector with adequate voltage if a wall outlet cannot be reached directly.
3. Locate the power button on the monitor and press it to turn the monitor on.
FreeSync
The feature itself is off by default when setting 75Hz refresh rate. In order to use this feature, please note you must have hardware with FreeSync capability, an HDMI cable, and the latest graphics drivers. To use this feature, connect your computer and monitor with an HDMI cable. After connecting, you may receive a prompt to enable the feature on your computer. If you do not receive the prompt, you may need to enable the function in your graphics card menu. See your graphics card manufacturer's documentation for instructions on how to turn on and/or enable FreeSync.
Indicator Light
Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light indicates no video source has been detected. A red light indicates that no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/or connected.
Operation
The On-Screen Display (OSD) Menu may be used to adjust your monitor’s settings and appears on the screen after turning on the monitor and pressing the button.
Note: When using the monitor for the first time, settings will automatically adjust to optimal settings according to your computer’s configuration and parts etc.
1. Press "" to activate the navigation window.
2. Press 
to enter the OSD menu.
3. Press or to browse functions.
- Highlight the desired function, then press to enter the sub-menu.
- Press or to browse sub-menus, then press to highlight the desired function.
- Press or to highlight an option, then press to confirm the settings and exit the current screen.
4. Press 
to exit the current screen.
| Main Menu Item | Submenu Item | Sub-Submenu Item | Description |
| Picture | Brightness | 0-100 | Adjusts the luminosity of the display. |
| Contrast | 0-100 | Adjusts and controls the detail in dark colours. | |
| DCR | ON | Adjusts the contrast of your display. | |
| OFF | |||
| ECO | Standard | Preset values that adjust the colour according to your purpose of use. | |
| Photo | |||
| Movie | |||
| Game | |||
| FPS | |||
| RST | |||
| Colour | Colour Temperature | Normal | Adjust the RGB Color scale of the monitor. |
| Warm | |||
| Cool | |||
| USER | |||
| Red | 0-100 | Adjust Red Color Of colour temperature(Only USER Mode) | |
| Green | 0-100 | Adjust Green Color Of colour temperature(Only USER Mode). | |
| Blue | 0-100 | Adjust Blue Color Of colour temperature(Only USER Mode). | |
| OSD Setting | Language | English | Changes the monitor menu language. |
| Espanol | |||
| Pусский | |||
| 简体中文 | |||
| 한국어 | |||
| 日本语 | |||
| F r a n cés | |||
| OSD H-Position | 0-100 | Moves the OSD To left or Right. | |
| OSD V-Position | 0-100 | Moves the OSD To Up or Down. | |
| OSD Transparency | 0-100 | Adjusts the opacity of the OSD. | |
| OSD Time Out | 0-60 | Adjusts the OSD time. | |
| Setup | Input Source | Auto Source | Automatic or manual selection of Sources to be displayed. |
| DP | |||
| HDMI1 | |||
| HDMI2 | |||
| Mute | ON | Adjust the monitor speakers mute on or not. | |
| OFF | |||
| Volume | High | Adjust the loudness of the monitor speakers. | |
| Low | |||
| Reset | N/A | Reset all variables to default values | |
| Firmware Update | NO | Update your monitor program with a USB flash drive. | |
| YES | |||
| Other | Aspect Ratio | Wide Screen | Adjusts the display’s ratio of width and height. |
| 4:03 | |||
| 1:01 | |||
| Auto | |||
| Low blue Light | OFF | Adjusts the blue light value to reduce. | |
| Low | |||
| Medium | |||
| High | |||
| MaxHigh | |||
| Response Time | ON | T urns on or off Overdrive For Faster Response Time.e. | |
| OFF | |||
| FreeSync | ON | Turns on or off AMD Freesync, enabling smoother gameplay. | |
| OFF | |||
| HDR | ON | Turns on or off HDR For Better PQ. | |
| OFF | |||
| LED Mode | ON | Turns on or off LED Mode To Control the monitor back cover LED lights.. | |
| OFF | |||
| ULMB | ON | Turns on or off MPRT For Faster Response Time(The refresh frequency must be greater than 100hz). | |
| OFF | |||
| Multi-Window | Multi-Window | OFF | Select multi-window mode. |
| PiP Mode | |||
| PBP 2Win | |||
| PBP 3Win | |||
| PBP 4Win | |||
| Sub Win2 Input | DP | Select the Source to be displayed in the second window. | |
| DP HDMI1 | |||
| DP HDMI2 | |||
| Sub Win3 Input | DP | Select the Source to be displayed in the Third window. | |
| DP HDMI1 | |||
| DP HDMI2 | |||
| PiP Size | Small | Change the size of the Sub Window in PIP mode. | |
| Medium | |||
| Large | |||
| PiP Position | Top Right | Change the position of the Sub Window in PIP mode. | |
| Top Left | |||
| Bottom Right | |||
| Bottom Left | |||
| Swap | Main Window | Invert the display interface of the Main Window and the Sub Window. | |
| Sub Window |
Specifications
|
Model |
KAMN34QUSA |
|
Screen Size |
34" |
|
Aspect Ratio |
21:9 |
|
Backlight |
E-LED |
|
Brightness |
MAX: 300cd/m2 |
|
Panel |
VA |
|
Resolution |
3440 x 1440 |
|
Refresh Rate |
75Hz |
|
Response Time |
25ms |
|
Viewing Angle |
3=178°(H) / 3=178°(V) |
|
Contrast Ratio |
3000:1 |
|
VESA Mounting |
100x100 |
|
Colours |
16.7M |
|
AMD FreeSync |
YES |
|
Signal Input |
DP1.2, HDMI1 (2.0), HDMI2 (1.4) |
|
Power |
DC 12V - 4A |
|
Audio |
|
|
Speakers |
YES |
|
Audio Out |
YES |
|
Accessories |
|
|
Adapter |
YES |
|
DP Cable |
YES |
|
Additional Functions |
|
|
Low Blue Light |
YES |
|
Flicker-Free |
YES |
|
Physical Dimensions |
|
|
Dimensions (w/Stand) |
827.42 x 368.92 x 57.0mm |
|
Dimensions (w/o Stand) |
827.42 x 495.1 x 244.37mm |
|
Net Weight |
6.65Kg |
|
Gross Weight |
8.82Kg |