Kogan Hunting Trail Camera 24MP - (KAHUTRCA810A) - Manual

 

Overview

 

 

 

Installation

 

If Using AA Alkaline Batteries

 

1. Pull the gap lightly and open the battery compartment.

 

 

2. Refer to the battery icons located on the inside of the battery compartment. Insert the batteries according to the positive and negative battery icons.

 

 

3. Close the battery compartment tightly to ensure water and dust resistance.

 

 

Note:
Installing any AA battery in the wrong direction may cause the batteries to leak acid or explode, causing camera failure and damage to the battery compartment.

 

If Using 6V DC Power Source

 

1. Remove the rubber port cap at the bottom of the camera. Plug a universal 6V DC cord into the bottom port.

 

 

2. Run the cord to the side of the camera where there is a hook provided behind the hinge of the camera door. This will support the power cord and take the pressure off of the connection point.

 

 

3. When not in use, replace the rubber port cap at the bottom of the camera to protect the 6V DC universal plug-in port.

 

 

Memory Card Installation

1. Insert the Micro SD card with the contacts facing away. The Micro SD card should slide in freely with little resistance. Continue pressing the card inward until you hear a click. This means the Micro SD card is locked in place and ready for use.

 

 

2. To remove Micro SD card, press the card inwards to release.

 

 

Operation

 

Quick Start

 

Slide the mode switch from OFF to TEST position to activate the camera and view the user setup screen.

 

 

There is a control panel with 8 keys when you open the camera.

 

Operating Buttons

 

 

MENU	Open the Settings menu using the MENU button.
REPLAY	Press this button to start the replay mode.
	Change to the manual recording mode for videos.
	Change to the manual recording mode for taking photos.
SHOT	Manually take a video or photo depending on the set recording mode. Video recordings are ended by pressing the SHOT button.
	Press it to start the video, press it again to stop.

 

Auto Recording Mode

 

After entering settings, slide the power switch to ON to enter auto recording mode. The motion indicator will flash red for about 5 seconds, after which the camera will start working. It will automatically take pictures or record videos when a person or animal enters into the area of the PIR sensor.

Caution: To avoid potential false triggers due to temperature and motion disturbances, do not aim the camera at a heat source (e.g. the sun, heated stone or metal) and remove nearby tree branches and twigs. The ideal direction to aim at is an open place to the north without nearby heat sources.

Note:

Generally, it is recommended to place the camera at a height of 1–2 Metres.

 

Advanced Settings

 

Camera	Video	Setup
Resolution Sequence ISO Delay Camera ID	Resolution Video length Record audio	Mode Language Time-lapse TV mode Date/Time Timer Password Format Default settings Version

 

Camera Menu Settings

 

 

Camera	Submenu	Description
Resolution	24MP, 20MP, 16MP	Photo size
Sequence	1/3/6/9	Number of photos taken sequentially
ISO	Auto,100,200,400	Camera exposure level
Delay	1/5/10/30 sec/min	Delay between shots
Camera ID	0-0-0 0-0-0	Camera ID

 

Video Menu Settings

 

 

Video	Submenu	Description
Resolution	1080P, 720P, VGA	Video size
Video length	10S, 30S, 60S, 90S	Time length of the video
Record audio	ON, OFF	Toggle sound capture

 

Setup Menu Settings

 

 

Setup	Submenu	Description
Mode	Camera, video, camera and video, interval	Image, video, image + video, image taken at set interval
Language	English, French, German	Camera menu language
Time-lapse interval	5/30/60 Min	Taking picture or video for every 5/30/60 minutes constantly
TV Mode	NTSC, PAL	AV output mode
Date/Time	2018-09-03 16:37:25	YYYY-MM-DD HH:MM:SS
Timer	ON,OFF	Enable operation only during set period
Password	****	4-digit password(universal password: 1314)
Format	SD Card	Format the memory card and delete all files
Default settings	Factory reset	Restore factory defaults

 

Slide the switch to “ON” to resume operation after changing settings.

Note:

Images and video can only be played back/previewed while in test mode, not auto recording.

 

Specifications

 

Power	4 or 8 x AA Alkaline/Lithium batteries external DC 6V~12V (3.5 x 1.3mm jack)
Connectivity	AV out (video cable not included)
Water resistance	IP65
Photo recording
Photo resolution	24MP
File format	JPG
Time-lapse mode	5min/30min/60min
Multi-shot mode	Up to 9 photos per detection
Stamp (photos and video)	Date, time, temperature (˚C/˚F) and moon phase
Capture mode	Colour by day, black and white by night
Video recording
Video resolution	1920 x 1080/30fps (FHD)
File format	AVI/H.264
Sequence length	Adjustable from 10 to 90s
Capture mode	Colour by day, black and white by night
Audio
Sound recording	ON/OFF
Memory storage
Support	External only: Micro SD card up to 64GB
Detection system
Motion sensor	2 x PIR
Detection angle	120°
Detection range	Adjustable from 1 to 80ft
Trigger speed	0.3sec
Delay between each detection	Adjustable from Instant to 30min
Nighttime illumination system
LEDs	44LEDs
Flash range	<90ft
Exposure	Automatic infrared level adjustment
Optical field of view	120°
Dimensions	135mm x 90mm x 76mm
Operating temperature	-20°C to +70°C

 

Troubleshooting

 

The Camera Doesn’t Capture the Subject of Interest

• Check the PIR sensitivity for warm environmental conditions. Set the Sensor Level to “Low”, for cold weather use, set the sensor to “High”.
• Set your camera up in an area where there are no heat resources in the camera’s field of view.
• In some cases, setting the camera near water will make the camera to take images with no subject in them.
• Aim the camera over the ground.
• Set the camera on stable and immovable objects, i.e., large trees.
• At night, the motion detector may detect beyond IR illumination range. You can reduce the distance by adjusting sensor sensitivity.
• The rise or setting of the sun can trigger the sensor; reorient the camera.
• If a person or animal moves quickly, it may move out of the camera’s field of view before the photo is taken. Move camera further back or redirect camera.

 

The Camera Stops Taking Images

• Ensure that the memory card has enough memory storage. If the card is full, the camera will stop taking images.
• Check batteries to make sure that alkaline, NIMH or lithium AA batteries left power is enough for the camera to work.
• Make sure that the camera power switch is at the “ON” position and not at the “OFF” or “TEST” modes.
• Please format the memory card when you use it for the first time or use another memory card.

 

Night Vision Flash Range Doesn’t Meet Expectations

• Although the camera will operate well with 4 x AA batteries, 8 x AA batteries will improve performance and provide better battery life during night vision.
• Ensure that batteries are fully charged or left power is enough.
• High-quality 1.5V NIMH or lithium rechargeable AA batteries can offer superior flash range than alkaline batteries.
• To ensure accuracy and quality of nighttime image, mount the camera in a dark environment without obvious light sources.
• Having surfaces for the flash to bounce off (trees, walls, ground, etc.) within flash range is important to get good night time images. In an open field, there will be nothing for the light to reflect on and the images will be poorer.

 

In The Box

 

Camera	Quick Start Guide	Mounting Strap	USB Cable