Safety & Warnings
Attention
- Before charging, remove the rechargeable battery from the product.
- Charging should always be completed by an adult.
- Do not mix new and used batteries.
- The batteries should be installed with the correct polarity, the positive and negative connections should align with the indicator.
- Do not mix alkaline batteries with standard carbon batteries or rechargeable batteries.
- Do not subject the batteries to high temperature.
- Do not subject the batteries to impact.
- Do not put the batteries in water, they should be stored in a dry place.
- Always exercise caution around electrical outlets.
- Do not transport/store the battery with other metals(such as necklace/hairpin).
- Do not decompose or break the battery.
Note for parents
- Parents should guide children when installing or replacing the battery.
- Operation of the product might be affected if the surrounding has high electric power output. Please reset the product and stay away.
- Regularly check the plug and other accessories, if any damage is found, do not use until it is completely restored. The product is not suitable for kids under 3 years old.
Overview
Laser Gun
Armour
Martian Mechanical Beetle
Badge
Installation
Laser Gun Battery Installation
Use a screwdriver to unscrew the battery cover located in the handle of the gun. Install three new 1.5V AAA batteries into the battery compartment, observing the polarity markings. Reinstall the screw and tighten to close the battery cover.
Armour Battery Installation
Unscrew the screws at the back of the Armour and remove the battery cover. Load three 1.5V AAA batteries and replace the battery cover and screw.
Badge Battery Installation
Unscrew the battery cover located at the back of the Badge and insert 3 new AG13 button cell batteries to the battery compartment, observing the polarity markings. Use screw to close the battery cover.
Operation
Beetle
- Press the start button and the beetle will start to run. Press the button one more time to shut it off.
- Aim and shoot the beetle with the gun and the beetle will flip over when it is hit. It will immediately flip back over and continue to escape. After it is hit 6 times, the beetle will die.
- The maximum shooting distance between the gun and the beetle is ~6 metres. The beetle should be placed on a hard floor. Soft flooring like carpet or rough ground like dirt will affect the operation as the beetle will not move properly.
Beetle Battery Charging
Connect one end of the USB cable to the charging socket of the beetle, the other end to a computer. The charging time is ~20-30 minutes, the playtime is ~10-20 minutes.
Badge
- Slide the power switch on the badge to the “ON” position. The formation indicator light will flash and the HP indicator light will light up along with sound effects. The default team mode for the badge is Team Blue.
- Team formation: 4 team colours are available for selection: blue, red, green and white. Each colour is for one team. The same colour team will not hit each other during play. Press the team selection button to choose your team.
- During play, the badge will emit a sound when hit and the indicator light will flash quickly whilst the corresponding HP is subtracted.
Remarks: When HP reaches zero, the formation indicator light will flash quickly.
How to Play
Game 1: Gun to Gun (2 Persons)
Separate into two teams and defeat the other party.
Game 2: Gun to Badge
The hero holds the gun and the villain wears the badge. The hero and the villain are on different teams. The villain gets a head start. If the hero catches up and defeats the villain within 5 minutes, the villain dies, it is game over and the hero wins, the hero gets one point. If the hero didn’t defeat the villain within 5 minutes, the villain has escaped successfully and wins one point.
Game 3: Two Guns and Two Badges (2 Persons)
There are two teams, both with guns and badges. The two teams fight each other, until one team run out of HP and die. The other team wins and gets one point.
Game 4: Two Guns and Two Badges (4 persons)
The soldier protects the prince. Separate into two teams, team A and B, each team have two persons, the soldiers hold the guns and the prince wears the badge. The soldiers must protect the prince’s HP. When all of the soldiers run out of HP, the soldiers are lost and the prince can take the soldier’s gun and join the fight. Regardless of the soldier’s HP life value, the game will be over once the Prince’s HP life value comes to zero.
Game 5: 6 Guns and 2 Life Reborn Badges (6 Persons)
- Six people are divided into teams A & B, for a 3 VS 3 game. Each team member has one gun and each team has one badge, which is known and the Life Reborn Badge. During the game, if one member is defeated, he can be reborn (regain life) by using the badge.
- Being reborn can be completed by, wearing the badge and turning it on. Alternatively, you may wait for the other two teammates to defeat any one of the enemies. Then you can take the gun and keep fighting. Once the badge is used it cannot be used again. The other team members will also not be able to use it again.
- The main emphasis of this game is to destroy the Reborn Badge and reduce any team member’s HP life value to zero, that team will lose and the game is over.
Troubleshooting
Issue |
Reason |
Solution |
The device can’t be operated |
The controller couldn’t link the device |
Turn on the power switch, aim the weapons against each other |
The battery has run out |
Recharge the product or replace with new batteries |
|
The maximum distance has been exceeded, the infrared light can’t reach the product or is at the wrong angle |
Shooting distance of the Gun/Sword/Badge is ~20-25 metres Operating distance of Gun/Sword/Badge to Beetle is ~6 metres Operation angle is ~15 degree. The gun and other devices will not function unless this is adhered to. |
|
Barriers between the product and controller |
Remove the barriers |
|
Automatic operation |
Low power has caused intermittent operation |
Recharge the product or replace with new batteries |
The device is placed under strong light |
Remove the product from strong light or play without strong light |
|
There is influence from other infrared devices, such as a TV controller |
Do not use other infrared devices when you are controlling the product |
|
Attention: If the operation is interrupted or disturbed, it may be caused by a strong current. You can reset the product. If it still doesn’t work, try to reset the product in a different location or environment. To ensure the product is working in good condition, please change the batteries when the power is low. |