Safety & Warnings
- Do not use the headphones while driving or operating heavy machinery.
- Please put the headphones and accessories in a place that cannot be reached by children or pets as it may cause suffocation and serious consequences if swallowed or otherwise misused.
- Do not use the product outside of the recommended operating temperature, below -10°C or above 45°C. Extreme temperatures can cause deformations, reduce the charging capacity of the device and shortens the service life.
- Do not use the headphones while they, or you, are wet; liquid can cause severe damage to the product.
- Equipment damage caused by water is not covered under warranty.
- If you play at high volume for a long time, then it may damage your hearing. It is suggested to use at lower volume.
Operation
Initial Set-Up/Pairing
Ensure the charging case has been charged prior to attempting to set up/pair headphones.
Step 1: Once both the headphones are removed from the case they will automatically power on and a blue light on each headphone will flash 2 times. The left headphone will alternate between red and blue light when the connection process starts.
Step 2: Once the headphones are turned on wait for the voice prompt “Pairing” from the left headphone, this confirms that the headphones are searching for a connection.
Step 3: Go to the Bluetooth connection list on your smartphone or tablet and search for “Kogan W10 Wireless Headphones” Bluetooth name on your device. Click to connect.
Once connected, it prompts “Connected” and a blue light on each earbud starts to flash, indicating that the earbuds are connected to the Bluetooth device.
Functions
Auto Power On
When the headphones are removed from the case, they will automatically power on. Blue lights on each headphone will flash 2 times, and the left headphone will flash red and blue alternately when the connection process starts. Please note: The case must be charged for the headphones to automatically power on. If the case is not charged, the headphones can be manually turned on.
Manual Power On
Press and hold the main touch button on the R and L headphones simultaneously for about 3 seconds to power on. A blue light will turn on and begin to flash on the headphones followed by a “Power On” message through the headphones.
Auto power OFF
Place the headphones back into the case and close the lid. Once they are put into the case, they will automatically power off and begin charging when a red light flashes once on each headphone.
Manual power Off
Press and hold the main touch button on the R and L headphones simultaneously for about 3 seconds to power off. A red light will flash once after a blue light flashes once on the headphones and followed by a “Power Off” message through the headphones.
Music Play/Pause
Short pressing R or L touch button could play or pause the music.
Music Next/Previous
Double press the main touch button of L headphone to go to the previous song. Double press the main button of R headphone to go to the next song.
Voice Assistant/Siri
Hold the touch button to activate your voice assistant, such as Siri. Please note not all smartphones support this feature.
Answer Call
During an incoming call, press the main touch button of R or L headphone once to answer a call.
End Call
During a call, press the main touch button of R or L headphone to end a call.
Reject Call
During an incoming call, double click the main touch button of R or L headphone to reject a call.
Cancel Call
When dialling, short press R or L touch button to cancel a call.
Low Battery Alarm
When the headphones power is less than 20%, they flash a red light for every 30 seconds and followed by a “Low Battery” message through the headphones for every 5 minutes.
Low battery Shutdown
When the headphones run out of battery, they will automatically shut off.
Automatic Connection
After the initial set up and connection, the headphones will automatically connect to your device next time when you turn them on. (Please ensure the Bluetooth is active on your device for automatic connection)
Charging for Headphones
Put R and L headphones into the charging case and close the lid to start the charging process. The charging headphones will flash red until fully charged. Once fully charged, the red light will turn off.
Case Power Indicator
“Indicator light OFF” 100% power
![]() |
60% ~ 80%Power |
![]() |
20% ~ 60% Power |
![]() |
1% ~ 20% Power |
Specifications
Bluetooth version | V5.0 |
Bluetooth distance | 10-15m |
Charging voltage | 3.7V |
Battery capacity | 65mAh |
Charging case | 400mAh |
Charging time | About 1.5 hours |
Playing time | About 6-7 hours |
Standby time | About 200 hours |
Calling talk time | About 4 hours |
Water resistance | IPX4 |
Troubleshooting
If you have been unable to pair both headphones, please refer to this article: