Installation
Note: Please have a Phillips-head screwdriver and 4x AA batteries on hand before installation.
- It is recommended to have this installed by a professional.
- Please note that the connection line shouldn’t be pressed, bent or folded during installation.
- Before the installation, ensure the lock is suitable for the door, or the direction of the handle must be adjusted according to the door opening direction.
- While installing, the door must be in a half-open state until the installation is complete.
- After the installation is complete, test whether the front handle and back handle unlock/lock normally.
- If it does not work properly, please check if there has been an error during installation.
Installation Overview
1 |
Front panel |
12 |
Connection column screws |
2 |
Connection column |
13 |
Reverse lock knob |
3 |
Square steel |
14 |
Back locking paddle |
4 |
Lock body |
15 |
Deadbolt |
5 |
Connection line |
16 |
Latch-bolt |
6 |
Back panel |
17 |
Lock body screws |
7 |
‘SET’ button |
18 |
Connection column |
8 |
Connection column screws |
19 |
Keyhole |
9 |
Battery cover |
20 |
Emergency power port |
10 |
Battery cover screw |
21 |
Front handle |
11 |
Back handle |
|
|
Lock Assembly and Preparation
1. Confirm the Direction of the Door
This smart lock is suitable for 4 kinds of the door opening directions (Left Out/Left In/Right Out/Right In).
2. Drill the holes using the installation template
Carefully measure and then drill the correct holes in your door to facilitate installation. This should be completed by a professional.
An installation template is included with your lock, outlining the location of the holes that must be drilled.
A copy of this template can be downloaded here:
Installation Template
3. Changing the Handle Direction
Check if the handle direction is appropriate for the door (facing left or right). It is not the correct direction, this can be changed as outlined below:
- Front Handle Orientation
- Remove the direction-changing screw, carefully and slowly twist the handle clockwise 180°, then retighten the direction-changing screw. Check the handle to make sure it isn’t stuck in place and can be used.
- Back Handle Orientation
- Remove the direction-changing screw, carefully and slowly twist the handle clockwise 180°, then retighten the direction-changing screw. Check the handle to make sure it isn’t stuck in place and can be used.
Match the front handle and back handle to make sure they are facing the correct direction.
Installing the Lock Body
Choose the installation direction of the latch-bolt of the lock body according to the door opening
Change the direction of the lock body.
- Push the reversing block to the other side.
- Push the latch-bolt into the lock and turn it 180 degrees.
- Put back the reversing block and the latch-bolt will pop up automatically.
Put the lock body into the door frame and tighten with 2 fixing screws.
Choose the Parts
Choose suitable parts according to the following table:
Door thickness |
Square steel length |
Connection column length |
Connection column screw length |
4-5.5cm |
8cm |
3.5cm |
3cm and 5cm |
5.5-6cm |
8cm |
5.5cm |
3cm and 5cm |
7-8cm |
10cm |
5.5cm |
5cm and 7cm |
9-10cm |
12cm |
5.5cm |
7cm and 9cm |
>10cm (Optional) |
14cm |
5.5cm |
9cm and 11cm |
Installing the Lock
Installing the Front Panel
- Install 2 connection columns on the front panel.
- Adjust the dot direction on the square steel sleeve with reference to the sticker on the rubber mat
- Left open - keep the dot left or right
- Right open - keep the dot at the top or bottom
- Insert the correct sized square steel into the lock body.
- Pass the connection line through the door hole.
- Align the square steel with the square steel hole of the front panel and fix the front panel on the door, then press the other end of the square steel.
Installing the Back Panel
- Press the front panel and connect the connection line with the corresponding interface of the back panel, then insert the excess line into the door hole.
- Insert the back-locking paddle into the lock body. You can cut off one or two sections of the back-locking paddle according to the thickness of the door.
- Note: The length of the back-locking paddle should not exceed the thickness of the door.
- Align the square steel with the square steel hole of the back panel and compress the back panel.
- Lock with 2 connection column screws to fix the back panel.
- Install 4x AA batteries and the battery cover, then lock the battery cover with the screw.
Note: When installing the back lock, please look through the screw hole and make sure the connection wire is not blocking the connection column hole to avoid damaging the connection wire when installing the screw.
Installing Buckle Plate and Buckle Box
Debugging
Please always keep the door in a half-open status when debugging.
- Check whether the following functions can be achieved or not.
- Press down front handle: latch-bolt/deadbolt remains locked in locked status.
- Press down front handle: latch-bolt/deadbolt retract in unlocked status.
- Lift up front handle: deadbolt stretches out in any status.
- Press down back handle: latch-bolt/deadbolt retract in any status.
- Lift up back handle: deadbolt stretches out in any status.
- When locking in the reverse direction from inside, press down the front handle/back handle, the latch-bolt/deadbolt should not move.
- Verify other functions are normal or not, including self-locking, virtual password, setting button, app remote unlocking etc.
Using the App
Installing the App
Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).
Creating a SmarterHome Account
If you do not have a Kogan SmarterHome account, register or sign in with a verification code sent by SMS.
To register:
- Tap to enter registration page.
- The system automatically recognises your country/area. You can also select your country code manually. Enter your mobile number/email address and tap “Next”.
If you choose the mobile number option, then enter the verification code sent to you by SMS. Set a password as prompted and press “Confirm” to finish your registration.
Create a profile on the next page to define your location and room.
Adding Device through Network
- Power the SmarterHome device ON and follow the product-specific instructions to enter the Wi-Fi-connect mode.
- Open Kogan SmarterHome app and tap “+” in the upper right to add a new device through the network.
- Select the type of device you want to connect to on the next screen.
- Ensure the device’s indicator light rapidly flashes and tap “Confirm light is rapidly flashing”.
- Select Wi-Fi network (Note: Network must be 2.4GHz band) and enter the password.
The device will commence the pairing process and connect to the app. - If needed, short press ‘3’ & ‘#’ on the lock to verify the administrator.
- During connection, the LED for ‘8’ will flash quickly.
- The Wi-Fi network of the app and device should be the same.
- After successfully configuring the devices, the device will be shown on the home page. Tap to enter its control page.
- Once added successfully, a voice will sound saying ‘Added successfully’.
- If addition has failed, an LED light will show ‘X’ and a voice will sound saying ’Add failure’. Please try to connect the unit again if this occurs.
To remotely open the door:
- Press ‘4’ and ‘#’ to activate the lock.
- Press the icon ‘Click open remotely’ when it flashes.
Operation
Using the Lock
Adding the Administrator (The first 3 users are administrators)
- Remove the battery cover, short press ‘Set’ (back panel) or long-press ‘*’ and then a voice will prompt: ‘Please add administrator’.
- Add the administrator’s fingerprint (3 times), card or password (6-8 numbers) followed by ‘#’ (the same password must be entered again as a confirmation).
- A voice will say: ‘Added successfully’.
- Then you can continue to add users.
Notes:
- Different position fingerprints can be added to improve the fingerprint identification rate.
- ‘*’ is used as the back and sign out button, while ‘#’ is used as the confirm button.
Adding a User
An administrator is required to verify and assist in adding another user.
- Remove the battery cover, short press ‘Set’ (back panel) or long-press ‘*’ and then a voice will prompt: ‘Please verify the administrator’.
- Verify the administrator.
- Add the user’s fingerprint (3 times), card or password (6-8 numbers) followed by ‘#’ (the same password must be entered again as a confirmation).
- The voice will say: ‘Added successfully’.
- Then you can continue to add users.
Deleting a User
- Remove the battery cover, short press ‘Set’ (back panel) or long-press ‘*’ and then a voice will prompt: ‘Please verify the administrator’.
- Verify the administrator.
- Short press Set (back panel) or long-press ‘*’ again.
- Press ‘1’ to remove all user fingerprints, press ‘2’ to remove all user passwords, press ‘3’ to remove all user cards and press ‘4’ to remove all users.
- The voice will then say ‘Successful’.
Note: The administrator can’t be removed by doing this, only normal users.
Modify Password
- Press ‘7’ and ‘#’ and you will hear a long beep from the lock.
- Enter the old password that is to be changed. The lock will prompt “Please add user”.
- Enter the new password followed by ‘##’. The lock will then prompt “Successful”.
Note: The old password that was modified will be invalid after the change.
Reset the Lock
- Remove the battery cover, long-press ‘Set’ for 3 seconds and verify the administrator.
- The system will restore itself to factory default settings.
Notes:
- After the reset, all user and administrator information is removed.
- The password will return to its default ‘1234567890’.
- Please add a new administrator immediately.
Self-locking
If the password is entered wrong 5 times in a row, the system will be locked for 180 seconds (3 minutes). Using the fingerprint or card unlock can remove the self-lock.
If the fingerprint is entered wrong 5 times in a row, the system will be locked for 180 seconds (3 minutes). Using the card unlock can remove the self-lock.
Low Power Warning
When the battery power is lower than 4.8V, the lock will prompt ‘The battery is used up, please replace it’. Please replace with 4 new batteries soon after. Do not mix brands or new and used batteries.
Virtual Password
Enter a virtual password before or after the real password and it can then be unlocked.
Volume Adjustment: Press ‘3’ ‘3’ ‘3’ ‘#’ to change volume (Mute, Low, Medium, High).
Doorbell: Press ‘#’ in the standby or initial state to sound.
Specifications
Fingerprint sensor |
Semiconductor |
DPI |
500 |
Identify time |
0.3s |
Unlock way |
Fingerprint, Card, Password, Key and App |
System capacity |
100 |
Supply voltage |
6V |
Low voltage warning |
4.8V |
Standby current |
<=50µA |
The user manual is subject to change without notice. For the latest version of your user manual, please visit https://www.kogan.com/usermanuals/