Please handle this product with care and inspect it regularly to ensure it is in good working order. If the product, power supply cord or plug shows any signs of damage: stop use, unplug and contact Kogan.com support. |
Safety & Warnings
- Position the ice maker on a flat, stable surface.
- This ice maker can only be used indoors.
- The installation or any malfunctions of the ice maker should be handled by a qualified technician. Do not attempt repairs on the Ice Maker.
- If the power cord is damaged; it must be replaced by a qualified person to avoid serious danger.
- Do not immerse this product in water or use a pressure washer to clean the ice maker.
- Do not cover this appliance when it is in operation.
- Never tilt the appliance more than 45° from the vertical position.
- Use the appliance only with drinking or potable water.
- This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children should not use or play with the appliance.
- Please keep all the packaging materials away from children and pets.
- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
- It is normal for the compressor and condenser surface to reach temperatures between 70°C and 90°C during operation and surrounding areas may be very hot. Ensure there is adequate room for ventilation.
- Due to fast freezing, ice cubes may appear “Cloudy”. This is due to air trapped in the water and will not affect the quality or taste of ice.
- Warning: Keep all ventilation openings clear from obstruction. The unit should not be boxed in without adequate ventilation.
- Warning: Do not use mechanical devices or other means to accelerate the defrosting process.
Overview
1 |
Top lid |
7 |
Ice full sensor |
2 |
Control panel |
8 |
Fan cover |
3 |
Sliding door |
9 |
Water outlet |
4 |
Ice storage tank |
10 |
Water inlet |
5 |
Fan |
11 |
Power cord |
6 |
Evaporator |
|
Spare Parts with the Unit
No |
Description |
Picture |
Quantity |
1 |
Anti-drain plug |
![]() |
2 |
2 |
Adaptor |
![]() |
1 |
3 |
Water pipe(1m) |
![]() |
2 |
4 |
Ice scoop |
![]() |
1 |
5 |
Filter bracket |
![]() |
2 |
Installation
This Ice Maker can be used with or without an external filter, depending on your preference.
If you would like to use an external filter, please note that a filter is not included with the Ice Maker, and is an optional accessory. The Ice Maker features mounting brackets (spare part number 5) for a 10" x 2" Inline Water Filter.
If you are not using a filter with your Ice Maker, you can follow the steps below, otherwise, skip to the “Installing with a Filter”.
Installation without a Filter
Step 1 |
Insert the inlet water pipe into the adaptor as shown. |
![]() |
Step 2 |
Remove the adapter from your wall water tap if applicable,then connect the Ice Makers adaptor and pipe to the water tap. |
![]() |
Step 3 |
Take off the anti-drain plug from back of the unit, and then connect water pipe to the hole as stated on the unit. |
![]() |
Step 4 |
If you need to take off the pipe or replace it, please do as follows: Firstly, take off the blue ring (“A”), then press the white ring (“B”), and take out the water pipe. |
|
Installation with a Filter
Step 1 |
Insert the filter bracket into the holes at the back of the unit. |
![]() |
Step 2 |
Take off the film from the filter and take off the covers from both side (filter is not included with the unit). |
![]() |
Step 3 |
Thread the filter connectors to two sides of the connector. |
![]() |
Step 4 |
Push the filter into the filter bracket; make sure the flow direction on filter is from left to right. |
![]() |
Step 5 |
Insert the inlet water pipe into the adaptor as shown. |
![]() |
Step 6 |
Connect the pipes to both sides of the filter, before connecting the pipe to the unit, please let the filter purge any debris or discoloration as described in step 8. |
![]() |
Step 7 |
Remove the adapter from your wall water tap if applicable,then connect the Ice Makers adaptor and pipe to the water tap. |
![]() |
Step 8 |
Put a container beside the unit and then let water flow over the filter for 30 seconds, until the water comes through clean. |
![]() |
Step 9 |
Take off the anti-drain plug from back of the unit, then connect water pipe to the hole as stated on the unit. |
![]() |
Step 10 |
If you need to take off the pipe or replace it, please do as follows: Firstly, take off the blue ring (“A”), then press the white ring (“B”), and take out the water pipe. |
![]() |
Once the water is connected, plug in the Ice Maker.
WARNING: Always ensure that the plug, your hands, and the surrounding area has been completely dried prior to plugging in the unit.
Operation
Control Panel Operation
Area |
Mark |
Description |
Indicators |
Add Water |
Check the water supply. |
Timing |
Timer is working or time is under setting. |
|
Ice |
Unit is under ice making process. |
|
Ice Full |
Ice is full, need to be taken out. |
|
Clean |
Unit is under auto clean process. |
|
![]() |
LED screen. |
|
Buttons |
![]() |
Button to change time setting. |
On/Off |
Turn on/off the unit. |
|
Timing/Clean |
Set timer function or turn on auto clean function. |
Step 1:Timer setting:Before pressing the On/Off button, press the Timing/Clean button. The indicator Timing will light up, press + or - to adjust the timer alert time. If the timer function is set, the indicator will light up.
Step 2:Press the ON/OFF button to have the unit start making ice cubes. The LED screen will display room the temperature.
Step 3:The ice making time can be adjusted by pressing +/- directly.The ice making time will be shown on the LED screen.
Step 4:Auto clean function:Before the unit is turned on,long press the Timing/Clean button for 3 seconds for the unit to enter the auto clean mode.The water will flow for 30 minutes.
Step 5:Press the On/Off button again to turn off.
Cleaning & Care
- Clean the inner liner, water box, ice shovel and evaporator frequently. When cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to clean the inner and outer surface of the ice maker. Do not spray the ice maker with chemicals or diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.
- Keep ventilation openings in the appliance enclosure or in the built-in structure clear from obstruction. Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
- If the machine is reused after a long time, the water pump may not pump sufficient water due to the air inside, the “Add Water” indicator light will turn on in this case. To correct this, press the START button again and then the machine will work normally.
- To ensure the cleanliness of the ice cubes, water in the water reservoir should be replaced every 24 hours.
- If the compressor stops for any reason such as water shortage, too much ice, power off, etc. Do not start the system right away, wait for 3 minutes and then re-start the ice maker.
- Always change water before starting ice production at initial installation or after long shut-off periods.
Specifications
Ice making capacity |
60kgs |
Ice size |
22 x 22 x 15mm |
Ice storage capacity |
10kgs |
Dimension |
457 x 432 x 744mm |
Voltage |
AC 220-240V/50Hz |
Power cord |
3 pins grounded plug |
Troubleshooting
- Please note, if the water filled to the evaporator is not symmetrical, small sundries maybe formed and lodged in the pipe, which mean that water will be filled to the evaporator causing it to jam.
- Please pull out the cap of the pipe, then let the water through the pipe in order to clean the pipe and then you can replace the cap. It will make formal ice cubes.
Problem |
Possible cause |
Suggested solution |
The compressor works abnormally with a buzzing noise |
The voltage is lower than recommended |
Stop the ice maker and do not restart until the voltage is normal |
Indicator light on the display is not on |
1. Control panel wire line is loosened 2. Control panel is broken |
Contact Kogan support |
The water is flowing, ice is made, however no release of ice |
Temperature sensors are connected wrongly |
Contact Kogan Support |
Everything is correct but no ice is made |
1. Refrigerant leaks 2. Cooling system blocked |
Contact Kogan Support |
Disposal
Electrical and battery-operated units that don’t work should not be disposed of with normal household waste. They are to be collected separately, in accordance with the 2002/96 EC Directive for the disposal of electrical and electronic waste and sent for proper and environmentally friendly recycling. Please check with your local authority for further information.