Return to Kogan.com Account Login

Kogan 32" LED TV (Series 5 QH5000) - (KALED32QH5000QB) - User Manual

mceclip0.png

Safety & Warnings

Handle with care and inspect regularly to ensure the product is in good working order.

If this product, power supply cord or plug shows any signs of damage: stop use, unplug the product and contact Kogan.com support.

General Safety Instructions

Risk of electric shock. DO NOT OPEN! Do not attempt to service the television yourself, as opening or removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to the Kogan customer support team.

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The television should not be exposed to dripping or splashing and no liquid filled objects such as vases should be placed on the case.

In the event of smoke, strange noises or a strange smell from the unit, you should follow these steps:

  • Turn off the unit immediately.
  • Disconnect the power plug from the power outlet.
  • Contact the Kogan customer support team. Never attempt to make repairs yourself.
Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill any liquids onto the set. Use special caution in households where children are present. The television is not suitable for children under 4 years old to operate.

Power supply cords should be routed safely to prevent dangers due to damaged cords. The mains plug is the main disconnect method, so it should be easily accessible and not be obstructed during use.
To avoid fires, no naked flame sources such as lit candles or burning incense should be placed onto the casing of the television.
Do not pull the plug out of a power outlet by pulling on the power cable. Always grasp the plug and pull. Never touch the plug with wet hands.
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal.
Always turn the set off when it is not being used. Unplug the television from the power outlet when it will not be used for a long time or when there is an electrical storm. Never touch the antenna cable during a lightning storm.
Excessive volume from earphones and headphones can cause permanent hearing loss. Always monitor the volume of noise from these devices, especially when children are using them.

Installation

Ventilation should not be impeded or limited by covering the ventilation slots with items such as newspapers, tablecloths, curtains etc. At least 10cm of space should be left around the apparatus for sufficient ventilation.
The television should be situated away from heat sources such as radiators, heaters, stoves or other products that produce heat. Place the television in a position where the screen is not exposed to direct sunlight. It is best to have soft indirect lighting while watching and you should avoid a completely dark viewing environment and reflections to avoid eye fatigue. Keep the product away from high magnetic fields (such as near an amplifier speaker) to avoid affecting the tint.
Do not place the television on an unstable table, stand or shelf. The set may fall, causing serious injury as well as damage to the television itself. If moving the television on a cart, move the unit with care as sudden stops and starts may cause the television to overturn.
Do not place this television near water, for example near a bathtub, wash bowl, kitchen sink, laundry tub, swimming pool or in a damp basement etc.
When moving the television to a warm location from a cold location, allow some time for any dew or condensation inside the television to evaporate fully before you turn the unit on.
To prevent injury, the television must be securely attached to the floor/wall in accordance to the supplied installation instructions.

Cleaning

Unplug the television from the power supply before cleaning. Do not use any liquid cleaners or harsh chemicals. Use a soft, damp cloth.

Overview

Control Panel Button Functions

VOL+: Volume up.

VOL-: Volume down.

CH+: TV channel up.

CH-: TV channel down.

MENU: Press to select the main menu.

SOURCE: Select the input signal.

TV Terminal Connections

 

mceclip0.png

  1. USB input terminal.
  2. Audio / Video input terminal.
  3. RF antenna input.
  4. HDMI 1 input terminal.
  5. HDMI 2 (ARC) input terminal.
  6. COAXIAL output terminal.

 

Remote Control

mceclip2.png

mceclip3.png: Press this button to turn the TV on or off.
mceclip5.png : Press this button to mute or restore sound.
NICAM/A2: In TV mode, press this key to select the stereo mode.
ASPECT: Press to adjust picture ratio.
PMODE: Select picture mode.
SMODE: Select sound mode.
0-9: Select and switch to a channel using 0 - 9.
-/---: Switch the program digit.
mceclip6.png : Switch back and forth between the current and previous channels.
DISPLAY: Display TV information.
FREEZE: Press to freeze the current picture.
mceclip7.png: Press to start recording.
AUTO: Adjust the picture automatically in pc mode.
RED, GREEN, YELLOW, BLUE: Correspond to the different coloured options depending on the menu.
SLEEP: Set the sleep timer.
SOURCE: Press to change the signal source.
ENTER: Enter the selected option or execute the selected operation. Press this button to display "channel list" while in TV source.
MENU: Press this button to enter the main menu.
EXIT: Exit the OSD (On-screen display).
CHmceclip10.png/CHmceclip11.png: Change the channel up and down.
VOLmceclip10.png/VOL mceclip11.png: Adjust the Volume.
SUBTITLE: Turn subtitles on or off. (Used in DTV mode only)
T.SHIFT: Press this button to pause the current DTV program. (Used in DTV mode only)
Hold: Freeze a multi-page passage on screen in Teletext mode.
mceclip12.png: Press to start playing the MEDIA or to pause playing.
REVEAL: Press this button to reveal the hidden information on the Teletext page. Press again to hide the information.
mceclip14.png: Press to play backward
SIZE: Display the top, bottom or all of page to read easily in Teletext mode.
mceclip15.png: Press to play forward.
INDEX: Press this button to go to the index page in Teletext.
mceclip16.png: Stop playing the Media.
mceclip17.png: Skip to the previous chapter
S.PAGE: Turn on SUBCODE in the text while entering the text display mode.
mceclip18.png: Skip to the next chapter
TEXT: Press to enter the Teletext mode.
FAV: Switch between customer set "Favorite List" channels.
AUDIO: Press to select DTV audio.
DTV: Press to switch to DTV (Digital TV) mode. Press this button to display "Record list" in DTV
EPG: Enter the electronic program guide.
TV/RADIO: Switch between TV and RADIO

First Time Set up

If this is the first time you are turning on the TV and there are no channels tuned, the installation guide menu will appear on the screen.

  1. Press the "mceclip11.png/▼/◄/►" button to select the OSD (On-Screen Display) language.
  2. Press the "mceclip11.png/▼/◄/►" button to select energy mode.
  3. Press the "mceclip11.png/▼/◄/►" button to select your country.
  4. Press the "mceclip11.png/▼/◄/►" button to select the tuner type.
  5. Press the "mceclip11.png/▼/◄/►" button to select mode: DTV+ATV, DTV & ATV. Note: ATV has been turned off in Australia so only DTV will bring results.
  6. Press the "mceclip11.png/▼/◄/►" button to select LCN (Logical Channel Number) "ON" or "OFF".

mceclip19.png

Note: Searching for platform will take a long time, please be patient!

Channel Menu

You can tune for channels, set favourite channels and edit channels from this menu.

Press the MENU button to display the main menu.

Press the ◄ / ► button to select CHANNEL in the main menu

mceclip20.png

Press the mceclip11.png/▼ button and then press the ► button to choose Antenna or Cable.

1. Auto Scan

This will allow you to search for channels to tune your TV to.

  • Press "mceclip11.png/▼" button to select "Auto Scan"
  • Press "mceclip11.png/▼" button to select the try and press the "mceclip11.png/▼" button to select mode.

Note: ATV has been turned off in Australia so only DTV will bring results.

Press "mceclip11.png/▼" button and then press "►" button to start scanning. Press "MENU" or "EXIT" button to stop.

mceclip21.png

Note: Searching for channels may take longer than expected. Do not be alarmed if this takes a while to complete.

mceclip22.png

2. Analog Manual Scan

  • Press "mceclip11.png/▼" button to select "Manual scan" and press the "►" button to start the scan.
  • Press "MENU" button to return the previous menu.
  • Press "EXIT" button to exit the menu.

Note: Analog TV (ATV) has been turned off in Australia so this scan will not bring results.

3. Digital Manual Turning

  • Press "mceclip11.png/▼" button to select "Digital Manual Scan" and press the "►" button to start the scan.
  • Press the "MENU" button to return the previous menu.
  • Press the "EXIT" button to exit the menu.

4. Channel Edit

Press the "mceclip11.png/▼" button to select "Channel Edit" and press the ENTER button to enter.

a. DELETE

Press the "mceclip11.png/▼" button to highlight the program and press the RED button once to delete the program.

b. SKIP

Press "mceclip11.png/▼" button to highlight the channel you want to skip and press the "GREEN" button to skip. Press the "GREEN" button again to cancel the setting.

This means that the channel will be skipped over when channel surfing.

c. MOVE

Press "mceclip11.png/▼" button to highlight the channel and press the "BLUE" button to move. Then press the "mceclip11.png/▼" button to select where you want to move it to. Press the "BLUE" button again to confirm.

mceclip23.png

5. Signal Information (only used in DTV)

Press "mceclip11.png/▼" button to select "Signal information" and press the "ENTER" button to view. Press the "MENU" button to return the previous menu. Press the "EXIT" button to exit the menu.

mceclip24.png

Picture Menu

You can select the type of picture, or adjust the picture settings to best suit your preferences.

Press the "MENU" button to enter the OSD menu.

Press the "◄/►" buttons to select the "PICTURE" menu.

mceclip25.png

  1. Press the "mceclip11.png/▼" button to select "Picture Mode" and press the "◄/►" button to change the picture mode.
  2. Press the "mceclip11.png/▼" button to select "Brightness" and press the button to enter brightness
    adjustment menu to adjust brightness.
  3. Press the "mceclip11.png/▼" button to select "Contrast" and press the "◄/►" button to enter the contrast adjustment menu to adjust contrast.
  4. Press the "mceclip11.png/▼" button to select "Sharpness" and press the "◄ /►" button to enter sharpness adjustment menu to adjust sharpness.
  5. Press the "mceclip11.png/▼" button to select "Saturation" and press the "◄/►" button to enter Saturation adjustment menu to adjust saturation.
  6. Press the "mceclip11.png/▼" button to select "Hue’’ and press the "◄/►" button to enter hue adjustment menu to adjust hue.
  7. Press the "mceclip11.png/▼" button to select "Color Temp" and press the "◄/►" button to select mode: Standard, Cool, Warm.
  8. Press the "mceclip11.png/▼" button to select "Aspect Ratio" and press the "◄/►" button to select.
  9. Press the "mceclip11.png/▼" button to select "PC Setup" and press the "ENTER" button to enter sub-menu. Note: The 'PC Setup' item is used in PC mode only.
  10. Press "mceclip11.png/▼" button to select "Screen Mode" and press the "◄/►" button to select. Note: The 'Screen Mode' item is used in HDMI mode only.
  11. Press "mceclip11.png/▼" button to select "Advanced Settings" and press the "►" button to enter the Advanced Settings adjustment menu to adjust.

Sound Menu

You can select the type of sound, and adjust sound settings to best suit your preferences.

Press the "MENU" button to enter the OSD menu.

Then press "◄/►" button to select the "SOUND" menu.

mceclip26.png

  1. Press "mceclip11.png/▼" button to select "Sound Mode" and press the "◄/►" button to select mode. 
  2. Press "mceclip11.png/▼" button to select "Treble" and press the button to adjust.
  3. Press "mceclip11.png/▼" button to select "Bass" and press the "◄/►" button to adjust.
  4. Press "mceclip11.png/▼" button to select "Balance" and press the "◄/►" button to adjust.
  5. Press "mceclip11.png/▼" button to select "Surround sound" and "◄/►" button to select "ON" or "OFF".
  6. Press "mceclip11.png/▼" button to select "EQ Setting" and "◄/►" button to enter the EQ (Equalizer) Setting adjustment menu to adjust EQ.
  7. Press "mceclip11.png/▼" button to select "AVL" (Automatic Volume Leveler) and press the "◄/►" button to select "On" or "Off".
  8. Press "mceclip11.png/▼" button to select "SPDIF" and press the "◄/►" button to select .
  9. Press "mceclip11.png/▼" button to select "Audio Description" and press the "►" button to enter sub-menu to select.
  10. Press "mceclip11.png/▼" button to select "Sound Type" and press the "◄/►" button to select.

Lock System Menu

Press the MENU button to enter the OSD menu.

Then press ◄/► button to select the "Lock System" menu. The default password is "0000".

Note: The administrator password is "8899".

mceclip27.png

  1. Press the "mceclip11.png/▼" button to select "Enable" and then press the "◄/►" button to select "On" or "Off".
  2. Press the "mceclip11.png/▼" button to select "channel locks" and press the "►" button to select channel(s) to lock.
  3. Press the "mceclip11.png/▼" button to select "Parental Rating" and press the "◄/►" button to set.
  4. Press the "mceclip11.png/▼" button to select "Lock Keypad", then press button to select "On" or "Off". The keyboard will be invalid if you set Lock Keypad to "On".
  5. Press the "mceclip11.png/▼" button to select "Hotel Mode" and press the "►" button to enter the sub-menu to set.
  6. Press the "▼/▲" button to select "New Password" and set your new password.
  7. Press the "▼/▲" button to select "Clear Lock" and then press the "►" button to clear.

mceclip28.png

Setup Menu

Press the MENU button to enter the OSD menu.

Then press ◄/► button to select the SETUP menu.

mceclip30.png

  1. Press the "mceclip11.png/▼" button to select "OSD Language" and press the "◄/►" button to select the OSD language.
  2. Press the "mceclip11.png/▼" button to select "Audio Language" and press the "►" button to enter the Audio language adjustment menu to select the Audio language. Note: this will not automatically translate programmes. 
  3. Press the "mceclip11.png/▼" button to select "Subtitle" and press the "►" button to select "On" or "Off". Note: This function is only used for DTV.
  4. Press the "mceclip11.png/▼" button to select "Teletext" menu and press the "►" button to enter sub-menu.
  5. Press the "mceclip11.png/▼" button to select "Blue Screen" and press the "◄/►" button to select "On" or "Off".
  6. Press the "mceclip11.png/▼"button to select "Mode Setting" and press the "◄/►" button to adjust.
  7. Press the "mceclip11.png/▼" button to select "Time Setting" and press the "◄/►" button to adjust.
  8. Press the "mceclip11.png/▼" button to select "HDMI CEC Control" and press the "◄/►" button to adjust.
  9. Press the "mceclip11.png/▼" button to select "PVR Settings" and press the "◄/►" button to enter settings and adjust.
  10. Press the "mceclip11.png/▼" button to select "First Time Installation", then press "ENTER" button to view the same options as during first time set up.
  11. Press "mceclip11.png/▼" button to select "Reset", then press "ENTER" a dialogue. Press "◄" button selecting "Yes" to restore all setting to default setting.

PC Menu

Press the "MENU" button to enter the OSD menu.

Press "◄/►" button to select the "PC Setting" menu. (Only available in PC mode).

mceclip0.png

  1. Press the "mceclip11.png/▼" button to select "Auto Adjust" menu and press the "►" button to automatically adjust the screen.
  2. Press the "mceclip11.png/▼" button to select "H Position" (Horizontal) and press the "◄/►" button to adjust.
  3. Press the "mceclip11.png/▼" button to select "V Position" (Vertical) and press the "◄/►" button to adjust.
  4. Press the "mceclip11.png/▼" button to select "Phase" and press the "◄/►" button to adjust.
  5. Press the "mceclip11.png/▼" button to select "Clock" and press the "◄/►" button to adjust.

DTV Features

Favourite List

When the source is selected as DTV, users can enter the Favourite List by pressing the "FAV" button.

You can press the "◄/►" button to select the favourite list number.

mceclip1.png

Program Information

When the source is selected as DTV, you can press the "display" button to display the channel’s information. The program information window is shown as below:

mceclip2.png

 

Electronic Program Guide (EPG)

Electronic Program Guide (EPG) provides program information which is broadcasted now or in the future.

You can display the EPG window by pressing the "EPG" button.

DATE and TIME information is displayed along the top of the window.

The left side shows all channels. The right side shows the program on the channel. The selected program is also displayed on the top of this list.

mceclip4.png

  1. Press the "mceclip11.png/▼" button to select the "program". Press the "RED" button to enter record mode. Press the "GREEN" button to display program details. Press the "YELLOW" button to Check details of the PVR's Schedule List. Press the "Blue" button to enter reminder settings.
  2. Press the "mceclip11.png/▼" button to select "CH" and press the "◄/►" button to view the future programs for that channel.

Note: The USB disk will be formatted when used for PVR, please do not store important files in the USB disk, otherwise they will be deleted.

 

USB Media Playback

Press the "SOURCE" button to change to the "MEDIA" input.

mceclip6.png

Photo

mceclip18.png

  1. Press the "◄/►" button to select the "PHOTO" option and press the "ENTER" button to enter.
  2. Press "◄/►" button to select the disk drive you want to view, then press "ENTER" to enter.
  3. Press "BLUE" button to enter the submenu to set.
  4. Press the "EXIT" button to back to the previous menu.

Music

mceclip8.png

  1. Press the "◄/►" button to select MUSIC in the main menu, then press the "ENTER" button to enter.
  2. Press the "◄/►" button to select the disk drive you want to view/play, then press the "ENTER" button to enter.
  3. Press the "BLUE" button to enter the submenu to set.
  4. Press the "EXIT" button to back to the previous menu.

Movie

mceclip10.png

  1. Press the "◄/►" button to select MOVIE in the main menu, then press the "ENTER" button to enter.
  2. Press the "mceclip11.png/▼" button to select the disk drive you want to watch, then press the "ENTER" button to enter.
  3. Press the "BLUE" button to enter the submenu to set.
  4. Press the "EXIT" button to back to the previous menu.

Text

mceclip11.png

  1. Press the "◄/►" button to select TEXT in the main menu, then press the "ENTER" button to enter.
  2. Press the "mceclip11.png/▼" button to select drive disk you want to watch, then press the "ENTER" button to enter.
  3. Press the "BLUE" button to enter the sub menu to set.
  4. Press the "EXIT" button to back to the previous menu.

PVR Operation

To use the inbuilt PVR, you will require a USB drive. Plug this into the USB port on your TV. Make sure there are no important files on the USB.

In DTV source, press the "MENU" button to enter the OSD menu.

Press the "◄/►" button to select the Setup menu.

mceclip13.png

1. Press "mceclip11.png/▼" button to select "PVR Settings" and press the "ENTER" or "►" button to enter.

mceclip14.png

2. Press "◄/►" button to select "File Manager" and press the "ENTER" button to check PVR file system.

mceclip15.png

3. Press "◄/►" button to select "Device List" and press the "ENTER" button to the sub menu.

mceclip16.png

4. Press "mceclip11.png/▼" button to select "Scheduled Record" and press the "ENTER" button to set.

mceclip17.png

Note:

  1. The USB disk will be formatted when used for PVR, please do not store important files on the USB disk.
  2. Press the "•" button for the first time to start recording. The second time, the sign of recorder will be slimmed down, but it will still be recording.

Specification

RGB INPUT

Mode Resolution Horizontal Frequency (KHz)

Vertical Frequency

(HZ)
DOS 720x400 31.5 70
VGA 640x480 31.5 60
SVGA 800x600 37.9 60
XGA 1024x768 48.4 60
WXGA 1366x768 47.7 60

HDMI INPUT

Mode Resolution Horizontal Frequency (KHz)

Vertical Frequency

(HZ)
VGA 640x480 31.47 59.94
480i 720x480i 15.73 59.94/60
576i 720x576i 15.63 50
480p 720x480p 31.47 59.94/60
576p 720x576p 31.26 50
720p 1280x720p

37.50
44.96

 50
59.94/60
1080i 1920x1080i 28.13
33.75		 50
59.94/60
1080p 1920x1080p

56.25
67.5

50
59.94/60

COMPONENT (YPbPr) INPUT

Mode Resolution Horizontal Frequency (KHz)

Vertical Frequency

(HZ)
480i 720x480i 15.73 59.94/60
576i 720x576i 15.63 50
480p 720x480p 31.47 59.94/60
576p 720x576p 31.26 50
720p 1280x720p

37.50
44.96

50
59.94/60
1080i 1920x1080i 28.13
33.75		 50
59.94/60
1080p 1920x1080p 56.25
67.5		 50
59.94/60

Troubleshooting

Before contacting Kogan.com Support, check the following chart for possible solutions.

PROBLEM SOLUTION
TV will not turn on
  • Make sure the power cord is plugged in.
  • The batteries in the remote control may be exhausted; replace the batteries.
No picture, no sound
  • Check the cable between TV and antenna/ external AV device.
  • Press the power button on the remote.
  • Press the SOURCE button the remote, then press the "▲/▼" button repeatedly to select the TV source.
Poor picture, sound OK
  • Check the cable between TV and antenna/ external AV device.
  • Try another channel, the station may have broadcast difficulties.
  • Adjust the brightness/contrast in the Video menu. Check that the unit is set to PAL
Audio noise
  • Move any infrared equipment away from the TV.
Cannot connect to ARC
  • Please ensure that the device you are using ARC with is connected to HDMI 2.

Related articles