Safety & Warnings
Caution:
To avoid injury, please read this manual carefully before use.
- For safety purposes, do not stand on the running belt when starting the unit.
- Please stop immediately if you feel any nausea, or the units motion is no longer smooth.
- Always increase or decrease speed at a slow rate.
- Never adjust the belt during use.
- It is suggested to wear sports shoes when using the machine.
- Children, the elderly, pregnant women or patients should not use the machine.
- Alwaysclip the safety key on your clothing during use.
- Firmly hold the gripbars during use.
Safety Information:
- Place the machine on flat ground. Do not use the machine in the following locations:
- (The machine is specially designed for indoor use only).
- Any ground that is uneven.
- Any areas in high sunlight, or in close proximity to heating units.
- The input for the machine is AC 220V.
- An error may appear if the power is not stable. The unit must not have any other items connected to the same power socket, and should not be used through a power board.
- It is suggested to wear sports shoes and gym clothes when use the machine.
- Always increase or decrease speed at a slow rate.
- Be careful of children or surrounding objects when folding and unfolding the machine.
- Never put the machine near wet objects or areas. The unit may produce an error if it is wet.
Caution during use:
- If you do not feel well before use, please consult with your doctor.
- No liability will be accepted for improper use of the device, and any resulting injuries or damage.
- Please pull out safety key after use.
- Please pull out the safety key when moving or changing any parts of the machine.
- Children, the elderly, pregnant women or patients should not use the machine.
- Patients need a doctor’s consultation before use.
- Do not place any items within two meters of the machine.
- Do not start the machine when it is folded.
- Water should never contact the machine, especially the motor, power cable and plug.
- Never wear long dresses or other unsuitable garments during use.
- Do not use the machine in enclosed spaces, locations circulated air or flammable areas.
- Do not put any objects on the machine.
- Keep the plug away from heat.
- Please switch off the unit and remove the plug after using.
- Please do not stand directly on the belt while starting the machine.
- Do not disassemble the machine unless you are a qualified repair professional.
- Please make sure the running belt is fastened before use.
Assembly Instructions
Fasten the M16 knob and M6 knob in the corresponding positions.Please note the safety key placed in the middle of console and keep this free from the knob.
Overview
Hardware and Tools:
Serial NO. |
Part Name |
Spec |
qty |
unit |
1 |
Main Frame |
|
|
|
2 |
M6 Knob |
M6*20 |
1 |
PCS |
3 |
Fix knob |
M12*20 |
1 |
PCS |
4 |
Silicone oil |
|
|
PCS |
5 |
Hex wrench |
|
1 |
PCS |
6 |
Safety key |
Red |
1 |
PCS |
Overview Drawing
Parts List
Serial |
Part Name |
Spec |
qty |
unit |
1 |
Console PCB |
|
1 |
PCS |
2 |
Console up and down cover |
ABS |
1 |
SET |
3 |
Washer |
ABS |
1 |
PCS |
4 |
M6 Knob |
M6*12 |
1 |
PCS |
5 |
Armrest foam |
Cannot tear |
2 |
PCS |
6 |
Left and right Columns |
Q335 |
1 |
SET |
7 |
Power cord |
black、2150mm, |
1 |
PCS |
8 |
switch |
red |
1 |
PCS |
9 |
Pipe plug |
|
2 |
PCS |
10 |
Motor |
|
1 |
PCS |
11 |
External six angle screw |
M12*70 |
2 |
PCS |
12 |
M12 Knob |
M12*20 |
1 |
PCS |
13 |
Foot pads |
Nylon |
4 |
PCS |
14 |
Six angle screws in the cylinder head |
M5*40 |
2 |
PCS |
15 |
Wheel |
ABS |
2 |
PCS |
16 |
Self locking nut |
M5 |
2 |
PCS |
17 |
Motor down cover |
ABS |
1 |
PCS |
18 |
Controller |
|
1 |
PCS |
19 |
Frame |
Q235 |
1 |
PCS |
20 |
Strengthen the angle iron |
Q235 |
1 |
PCS |
21 |
Self locking nut |
M8 |
6 |
PCS |
22 |
Foot pad |
rubber |
2 |
PCS |
23 |
Left end cover |
nylon |
1 |
PCS |
24 |
Inner six angle screw |
M6*50 |
3 |
PCS |
25 |
Rear roller |
|
1 |
PCS |
26 |
Right end cover |
nylon |
1 |
PCS |
27 |
Cross head self drilling screws |
ST4.2*16 |
6 |
PCS |
28 |
Running board |
MDF |
1 |
PCS |
29 |
Socket Cap Screw |
M8*30 |
6 |
PCS |
30 |
Running belt |
Drill texture |
1 |
PCS |
31 |
Side rail |
PVC |
2 |
PCS |
32 |
Front roller |
|
1 |
PCS |
33 |
Pan head tapping screws |
ST4*12 |
2 |
PCS |
34 |
Strap |
140J |
1 |
PCS |
35 |
Console upper handle cover |
Q235 |
1 |
PCS |
36 |
Safety key |
red |
1 |
PCS |
Control Panel
- Ensure the safety key is in place and press the "START" key, the machine will start by counting down for 3 seconds with audible beeps before starting slowly at 1km/h.
- Press the "+" key to speed up and the "-" key to slow down. The fastest speed is 6km/h and lowest is 1km/h.
- Press the “DISPLAY" key to change the display between Distance,Time and Calories. When "scan" is selected the screen will automatically move between Distance,Time and Calories every 5 seconds.
- The treadmill has 3 inbuilt programs. To select a program ensure that the treadmill is in standby with the belt stationary. Press the "PROG" button to select the desired program then press “START” to start the machine.
- To stop the unit in an emergency, pull the red safety key. The machine will then stop. When the red safety key magnet is not in place the screen will show “Err”. When the Red safety key magnet is in place correctly the display will show “OFF”.
- Press "STOP" to stop the machine after use.
If any error codes appear on the screen, please attempt the following:
- ERR - Error without safety key - Please make sure the safety key is inserted.
- ERR - If the safety key is already on, but there ERR still shows or there is no function, then change the computer screen/display monitor.
- E2- Motherboard Error - Contact help centre.
- E4- Motherboard Error - Contact help centre.
- E5- Over current protection. Motherboard Error - Contact help centre.
- E6- Motor error – Motherboard or motor connection issue - Contact help centre.
- E7- Communication interruption – Connection error - Contact help centre.
- E8- Overload error- May have exceeded maximum weight.
Auto Mode:
Unfold Fold and Move
Unfold:
- Put the machine on the ground smoothly; open the handrail and tensile Knob.
Fold and Move:
- After use, please fold the machine and insert the tensile Knob. This will save space when not using the machine.
Daily Maintenance
Always disconnect the units power before checking the machine or cleaning.
- Clean the belt and dial plate with a slightly damp, clean cloth after use, or at least once a week.
- Check and tighten the screws and spines at fixing point.
- Do not hang clothes or other objects on the machine.
Usage of Silicone Oil
Pull up the running belt carefully. Apply silicone oil to running board. Then start the machine and let it run for 3 minutes without any weight applied. This should be completed after every 30 hours of use, as this will increase the lifespan for your unit.
Adjusting the Belt
1.If the belt is deviating to the left:
Start the machine and adjust to 2-3km/h.Without loading, use a hex key to tighten 1/4 of a rotation (see “01”). Let the unit run without loading 1-2 minutes. Repeat this process until the belt is centered.
2. If the belt is deviating to the right:
Start the machine and adjust to 2-3km/h.Without loading, use a hex key to tighten 1/4 of a rotation (see “02”). Let the unit run without loading 1-2 minutes. Repeat this process until the belt is centered.
3. Running belt has jammed
If the running belt is unable to move, use a hex key to tighten 1/2 a rotation on the left and right until the unit is able to move.