Safety & Warning
- Install the treadmill in a dry location away from water, dampness and dust.
- Do not run on the treadmill with bare feet. Wear appropriate exercise clothing.
- Plug the treadmill into a grounded electrical socket.
- Do not plug into an extension board.
- Keep children far away from the machine in case of accidents.
- Maintain the machine regularly.
- Switch off the machine after use.
- Ensure safety clip is attached to you before operating so the emergency stop will activate properly.
- After using silicone oil, please keep it in a place out of the reach of children to avoid serious result caused by accidental ingestion.
- Before using the machine, please check your clothes are buttoned up or zipped up.
- Don’t wear clothes that can easily hook onto the treadmill.
- Keep the power cord away from hot objects and surfaces.
- Keep children away from the treadmill.
- Don’t use the treadmill in the open air.
- Power off and unplug the treadmill before moving.
- Non-professionals are not allowed to disassemble the machine; otherwise, serious damage or injury may occur.
- Only one person can use the treadmill at a time.
- During the exercise, if you feel dizzy, chest pain, nausea or shortness of breath, please stop exercising immediately and consult your doctor.
- Do not use the treadmill if it is damaged in any way.
- Intended for home use only.
- Do not use when intoxicated.
- Do not exceed maximum weight of 150kg.
Ground Connection
- This product must be grounded. If the machine occurs malfunction, the ground will provide a path of least resistance for the current in order to reduce the danger of electric shock.
- This product is installed with equipment grounding conductor and power of ground plug. The plug must be inserted into the proper plug base that have been right installed and grounded according to the local laws or regulations.
- If equipment grounding conductor is connected improperly, it may cause the danger of electric shock. If you doubt whether the grounding of this product is right, please authorize professional electrician to check. Even if the attached plug with this product does not match with the plug base, it also can’t be transformed, please authorize professional electrician to install right plug base.
- Please make sure that the grounding plug of this product is connected to the plug base that has the same shape with it. This product can’t use plug base adapter.
Overview
Part no. | Name | Qty | Part no. | Name | Qty |
1 | Pedestal | 1 | 51 | Moving roller bush | 2 |
2 | Upright post(L) | 1 | 52 | Moving wheel | 2 |
3 | Upright post(R) | 1 | 53 | Square inner tube plug match 25*50*2.0T square tube | 5 |
4 | Incline frame | 1 | 54 | Plastic spacer ∮ 10* ∮ 15* ∮ 25*2*6 | 6 |
5 | Main frame | 1 | 55 | Edge strip buckle ∮ 25* ∮ 4.2*4.5 White | 8 |
6 | Computer frame | 1 | 56 | Plastic washer ∮ 10.5* ∮ 25*t1.5 | 2 |
7 | Massager Support | 2 | 57 | Assemble plastic 14*16*19 | 4 |
8 | Supine support | 1 | 58 | R-type wire clamp | 2 |
9 | Motor bracket | 1 | 59 | Sponge sheath ∮ 17* ∮ 70*130 | 4 |
10 | Running deck | 1 | 60 | Oil cap | 1 |
11 | Running belt | 1 | 61 | Dumbbell | 2 |
12 | Front roller | 1 | 62 | Compression spring ∮ 49* ∮ 5*5 | 2 |
13 | Rear roller | 1 | 63 | M5 L-shaped wrench | 1 |
14 | Motor belt | 1 | 64 | M6 L-shaped wrench | 1 |
15 | Gas spring | 1 | 65 | Cross open-end wrench | 1 |
16 | DC motor | 1 | 66 | Tubing bushing | 1 |
17 | Incline motor | 1 | 67 | Adjustment foot pad | 4 |
18 | Massager head | 1 | 68 | Round cushion | 8 |
19 | Computer PCB | 1 | 69 | Adjustment foot pad φ60* φ35*65*M10*22 | 2 |
20 | Computer keypad | 1 | 70 | Fuel tank | 1 |
21 | Lower controller | 1 | 71 | Fuel pipe | 1 |
22 | Grip pulse | 1 | 72 | M4 Flat washer | 6 |
23 | Speaker | 2 | 73 | M8 Flat washer | 26 |
24 | MP3 connecting line | 1 | 74 | M10 Flat washer | 4 |
25 | Safety lock | 1 | 75 | M8 Spring washer | 2 |
26 | Computer top line | 1 | 76 | M8 Locknut | 8 |
27 | Computer bottom line | 1 | 77 | M10 Locknut | 4 |
28 | 150 single line | 2 | 78 | Half-round head hexagon screw M8*15 | 2 |
29 | 300 single line | 2 | 79 | Half-round head hexagon screw M8*20 | 8 |
30 | 150 single ground line | 1 | 80 | Half-round head hexagon screw M8*30 | 5 |
31 | Power switch | 1 | 81 | Half-round head hexagon screw M8*40 | 1 |
32 | Upside-down T-shaped socket | 1 | 82 | Half-round head hexagon screw M8*45 | 1 |
33 | Power line (with tail plug) | 1 | 83 | Half-round head hexagon screw M8*65 | 6 |
34 | Computer top over | 1 | 84 | Half-round head hexagon screw M10*25 | 4 |
35 | Computer bottom cover | 1 | 85 | Half-round head hexagon screw M10*40 | 1 |
36 | Computer PCB top cover | 1 | 86 | Half-round head hexagon screw M10*55 | 1 |
37 | Computer PCB bottom cover | 1 | 87 | Cylinder head hexagon screw M8*12 | 2 |
38 | PU foam(L) | 1 | 88 | Cylinder head hexagon screw M8*60 | 3 |
39 | PU foam(L) | 1 | 89 | Cylinder head hexagon screw M8*70 | 1 |
40 | Rear cover | 1 | 90 | Countersunk head hexagon screw M8*25 | 8 |
41 | Side cover (L) | 1 | 91 | Cross recessed pan head screw ST3.0*10 | 11 |
42 | Side cover (R) | 1 | 92 | Cross recessed pan head screw ST4.0*10 | 23 |
43 | Motor top cover | 1 | 93 | Cross recessed pan head screw ST4.0*16 | 36 |
44 | Motor bottom cover | 1 | 94 | Cross head with flat self - tapping & self - drilling | 36 |
45 | Motor front protecting cover | 1 | 95 | Cross head self - tapping & self - drilling screws | 6 |
46 | Plastic edge strip (L) | 1 | 96 | Rubber gasket | 2 |
47 | Plastic edge strip (R) | 1 | 97 | Package stator | 1 |
48 | Body twister | 1 | |||
49 | Round inner tube plug match ∮19*T1.5 tube | 6 | |||
50 | Round inner tube plug match ∮ 32*T 1.5 Tube | 2 |
Assembly Instruction
Step 1:
- Raise the upper frame upright into position.
- Fix the control console into position with 79# screw and 73# flat gasket.
- Fix Upright post onto pedestal with 79# screw,83# screw and 73# flat gasket.
- Remove the package stator (red), used from transport, so that the treadmill can fold up for storage.
Step 2:
- Fix the left and right side covers on both sides of pedestal with 94# screw.
- Connect the electrical line and place it into small round tube, and then fix left and right handles onto electronic meter with 94# screw.
- Fix rear guard at the back of the end of the running belt with 94# screws. (Treadmill without accessories has finished assembly.)
Step 3: assembly of multi-functional supports
- Take out massager support, pay attention to (R) indication of (L) gasket, and fix the massager support onto left and right upright post with 79# screw and 73# flat gasket.
- Take out the supine leg support, and fix it onto the massager support with 81# screw, 73# flat gasket.
- Fix the massager head onto the top of the supine support with hex screw, flat gasket and spring washer.
Step 4: assembly of other components
- Install dumbbell onto allotted groove on the supine support.
- The body twister can be placed at any stable position by the user.
- Safety lock / Safety Tether should be attached to its position on the control console.
- Massage belt is hung in grooves on both sides of massager.
- Finally, please ensure that all screws are tightened after all accessories are assembled.
Operation
NOTE: Always use a power socket that is earthed.
- Insert power cord into the back of the treadmill and a power socket and turn on power switch on the back of the unit, it will light up red to indicate the treadmill has power. The treadmill will “beep” and the display will turn on.
- Attach the safety tether to your clothing and the tether insert on the console of the treadmill before activating the treadmills functions.
Massager and Multi-function Bracket
Power socket with ground line must be used for your safety when you use the massager.
- Always ensure the treadmill is unfolded in its functions position when utilising the massage function and other accessories.
- Sit ups can be performed by locking your legs into the multi-functional brackets and laying on the treadmill as demonstrated in the illustration.
Moving the Treadmill
1. Before moving the treadmill make sure it is turned off and unplugged from the power socket.
2. The running deck of the treadmill can be folded up towards the upper frame to move and store the unit.
3. The gas lift system will lock the running deck in the upright position.
4. Move the treadmill by placing a foot at the base to hold it steady and pull the treadmill back towards you by the hands.
5. Gently tread the gas spring casing as shown in the figure; the running platform will slowly fall to position to the ground.
Console Operation
Display
Button Functions
START: Start the treadmill.
STOP: Stop motor the treadmill.
PROG: Automatic Program, Custom program, HRC program and FAT Selection.
- When in manual mode press the PROG button to enter automatic program mode.
- Press PROG again to enter Body Fat Test mode.
- Press PROG again to return to manual control mode.
MODE: Selection of Countdown Mode.
SPEED: Running speed adjustment.
INCLINE: Incline speed adjustment.
When the console is in STANDBY state, press the MODE key to change from speed to incline adjustment.
VOLUME:Adjust volume of music playback.
Last/Next: Cycle between tracks during music playback.
Movement Modes
A. Manual mode function
When the treadmill is in standby, press the START key to start the treadmill and enter manual control mode.
The initial speed will be is 1 km/h.
Time, Distance and Calorie counts will start from 0.
Speed and incline of the treadmill can be adjusted in real time using the SPEED and INCLINE keys on the console.
If exercise time exceeds 99: 59 minutes, the time will reset to 0.
B. Countdown Mode
The treadmill can be set to stop when you reach a desired goal of either Time, Distance or Calories.
1). Enter Time countdown mode: In full manual operation mode state, press the Mode key to select the Time countdown mode, the Time window displays 30: 00 minutes and the running time can be set via Speed +/- key or Incline +/- key. Set time range from 8: 00 ~ 99: 00 minutes. Press the START key to start the timer countdown.
2). Enter Distance countdown mode: In full manual operation mode state, press the Mode key to select the Distance countdown mode, the window displays 1.0 km and the distance goal can be set by pressing the Speed +/- key or Incline +/- key, Set distance range 1.0 ~ 99.0 km. Press the START key to start the distance countdown.
3). Enter Calorie countdown mode: In full manual mode, press the Mode key to select the Calorie mode, the Calorie window displays 50 calories and can set by pressing the Speed +/- key or Incline +/- key. Set calorie range from 20 ~ 990. Press the START key to enter into the Calorie bump mode of operation.
During any countdown mode when START is pressed the initial speed will be 1 km/h.
The countdown down mode you have chosen will begin to countdown as the other paramters count up in regards to the treadmills operation.
The speed and incline of the treadmill can be adjusted manually in real time using the SPEED and INLCINE keys.
As the countdown parameter reaches its goal the treadmill will slow down and enter standby mode.
C. Automatic program functions
In Manual operation mode state or MODE setting state, press the PROGRAM key to enter the automatic program selection.
The TIME window displays 30: 00 minutes and can be adjusted by press the SPEED +/- key or INCLINE +/- key. Set range of 8: 00 ~ 99: 00 minutes.
Press the START key to get into the running of the automatic program.
The automatic program is divided into 20 sections. The Speed and Incline values for each segment run is determined by the automatic program. The run time for each segment is 1/20 of the total set time, the TIME window resets the count at the start of each segment.
Distance and Calories window from 0 and count up.
Speed and incline can be adjusted during the automatic program by pressing the SPEED and INCLIND keys.
When the automatic program is complete the treadmill will enter the standby mode.
D. Body Fat Test Function
In the initial standby or mode setting state, press the Program Key to select enter body fat test settings. After entering the body fat test settings status;
- The SPEED window displays the parameters name.
- The TIME window displays parameter value to be set.
- Adjust the parameter value by using SPEED +/- key or INCLINE +/- key.
- Press the MODE key to select and enter the next setting.
The first parameter is the Gender (F-1) Setting: Initial Value 1 (Set range 1 ~ 2. 1 for male; 2 for female)
The second parameter is the Age (F-2) Setting: Initial Value 25 (Set range 10 ~ 99 years old)
The third parameter is Height (F-3) set: Initial Value 170 (Set Range 100 ~ 220 CM)
The fourth parameter is Weight (F-4) set: Initial Value 70 (Set range 20 ~ 150 KG)
The fifth parameter is BodyFat (F-5) test: Initial Value ---
Body Fat Test: When all the parameter have been input it is time to test for Body Fat percentage.
At this point, put your two hands to hand the steel sensor plates on the handle bars for about 5 seconds.
The index for the body fat test will be calculated based on your input parameters and then displayed on the screen.
E. Heart Rate Function
Heart rate Function Test method:
Place the palm of your hands onto the twosteel plates of the left and right handle bars, respectively, use a natural grip on both handles.
After about 5 seconds, LED pulse display window will display a heartbeat initial value. Keep your hands still on the sensors for roughly 30 seconds to get an accurately heart rate measure.
The heart rate data will change in real time as long as your hands are placed on the sensors.
Note: Hand-to-hand heartbeat test data is not medically accurate and should be used for sporting purposes only.
F. Sleep Function
When the treadmill stops running and there is no operation for more than 10 minutes sleep mode will be activated. The control console automatically turns off the display. Press any key to wake it up.
G. Safety Lock / Safety Tether
The safety tether should be placed its specified location in the control console before you can the treadmill can be operated. If the safety tether is missing or not connected correctly the control console will displays E07 or "---" with a warning note. If the safety tether is removed during operating, the system will quickly shut down, and the safety lock will be closed again, all motion data is cleared.
USB Functions
Insert a USB containing MP3 audio while the treadmill is powered off. Audio will automatically play from the USB.
Display Parameters Range
Initial | Program Initial Value | Setting Range | Display Range | |
Time(Min:Sec) | 0:00 | 30:00 | 8:00-99:00 | 0:00~99:59 |
Speed(Km/h) | 0.0 | 1 | 1-18 | 1-18 |
Distance(Km) | 0.00 | 1.00 | 1.0-99.0 | 0.0-99.9 |
Pulse(Times/Min) | P | N/A | N/A | 40-199 |
Calories(Kcal) | 0.0 | 50.0 | 20-990 | 0-999 |
Incline(Level) | 0 | 0 | 0-20 | 0-15 |
Maintenance and Cleaning
Appropriate maintenance is needed to keep your treadmill in optimal condition. Incorrect maintenance will damage or shorten the service life of treadmill.
Regulate running belt
The running belt can be adjusted in two variables: degree of tightness and central position of running belt. The running belt has been adjusted when leaving the factory, but it will be stretched after use. Deviation from central position can cause damage by wearing the trim strip and rear protecting cover. It is normal for the belt to stretch throughout its use.
Adjust running belt
If the running belt is slips during use or tends to get caught and not run smoothly, it can be improve it by adjusting tightness of the belt.
Adjusting Running Belt Tightness
- Insert 5mm hexagon wrench into the regulating screw on the back left of running belt, and turn the wrench by 1/4 of a circle clockwise to regulate the rear roller to tighten the running belt.
- Repeat step 1 to adjust the screw on the right. Ensure that the regulating screw is turned by the same distance to make the rear roller parallel with the frame.
- Repeat step 1 and 2 until the running belt does not slip.
- Note: the running belt shall not be too tight, it could damage the running belt, roller bearing, increase pressure of front/rear roller, and cause abnormal sound or other problems. To reduce tension of running belt, please turn the wrench anticlockwise by same distance on both sides.
Adjust Running Belt Position
When using the treadmill, the force of your feet can differ causing pressure on running belt and making it unbalanced, which makes the running belt deviate from the centre potion. Such deviation is normal. It will return to the centre when nobody is running on the running belt. Adjustment is needed if the belt fails to return to the central position. Follow the steps to adjust the position of the belt.
- Activate the treadmill without a runner on it and adjust speed to 6KM/H.
- Observe the distance of the running belt to left and right edge strips.
• If the running belt tilts towards the left, turn the left screw by 1/4 of a circle clockwise with hexagon wrench.
• If the running belt tilts towards the right, turn the right screw by 1/4 of a circle clockwise with hexagon wrench.
• If the running belt is still not in the middle, repeat the above steps until it is in the middle. - Adjust speed to 16KM/H after adjusting running belt to the middle, and observe deviation of running belt and smoothness of running. Repeat steps of adjustment in case of deviation.
- Ensure that after the adjustment that the running belt is not getting caught from being too tight or slipping from being too loose.
- Note: the running belt shall not be too tight, it could damage the running belt, roller bearing, increase pressure of front/rear roller, and cause abnormal sound or other problems. To reduce tension of running belt, please turn the wrench anticlockwise by same distance on both sides.
Lubricating Oil
The treadmill is oiled when leaving the factory, but lubrication of treadmill should be inspected frequently to maintain the condition of the machine. The treadmill must be oiled after 1 year or running for 100h.
Lift one side of the running belt and touch the surface of running platform after running for 30h or 30 days. It is unnecessary to lubricate if there is silicone oil on the surface; if the surface is clearly dry, oil it as instructed below.
As shown in the figure, open the oil cap, pour the non-petroleum silicone oil into the oil port, after finished, turn on the treadmill to run for some time.
Note: Stop the treadmill to make the running belt still while lubricating. Use only non-petroleum silicone oil.
Cleaning
Frequently clean the treadmill to guarantee its service life.
Warning: Cut off the power when cleaning the treadmill. The power line must be pulled out from the socket.
After use: Clean sweat stains on instrument and other parts with clean towel and damp cloth.
Note: Do not use corrosive articles and liquid to prevent damage to electronic elements. Don’t expose electronic elements to sunlight.
Storage: Place the treadmill in clean and dry environment. Ensure that power switch is off and plug is not in power socket.
Troubleshooting
Fault |
Cause |
Solution |
Code |
||
E01 |
Poor communication between sensors and controller |
1. Inspect connections between sensors and control console PCB. 2. Display PCB no signal output. Replace Display PCB. 3. Controller no signal output. Replace controller. |
E02 |
Short circuit |
1. Open circuit or poor contact of motor. Replace motor or check connector. 2. Damage to power cable. Replace cable. |
E03 |
Failure of speed induction |
1) Speed sensor is damaged. Replace it. 2) Speed sensor is not in place. Adjust its position. |
E04 |
Over voltage |
Connected power does not match the machines rated power |
Replace motor/speed sensor. |
||
Replace controller. |
||
E05 |
Over current protection |
1. Overload. 2. Resistance of running platform is too high, and it shall be oiled. 3. Motor is damaged. Replace it. |
E06 |
Error during self-test diagnostic |
Replace controller. |
E07 |
Safety tether not is position |
Please connect safety tether |
Display PCB Safety lock system error |
Replace display PCB and repair. |