Safety & Warnings
|
Handle with care and inspect regularly to ensure product is in good working order. If this product, power supply cord or plug shows any signs of damage: stop use, unplug the product and contact Kogan.com support. |
General Safety Instructions
|
Risk of electric shock. DO NOT OPEN! Do not attempt to service the television yourself, as opening or removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to the Kogan customer support team. |
 |
|
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The television should not be exposed to dripping or splashing and no liquid filled objects such as vases should be placed on the case. |
 |
|
In the event of smoke, strange noises or a strange smell from the unit, you should follow these steps:
|
 |
| Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill any liquids onto the set. Use special caution in households where children are present. The television is not suitable for children under 4 years old to operate. |  |
|
Power supply cords should be routed safely to prevent dangers due to damaged cords. The mains plug is the main disconnect method, so it should be easily accessible and not be obstructed during use. |
 |
| To avoid fires, no naked flame sources such as lit candles or burning incense should be placed onto the casing of the television. |  |
| Do not pull the plug out of a power outlet by pulling on the power cable. Always grasp the plug and pull. Never touch the plug with wet hands. |  |
| An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal. |  |
| Always turn the set off when it is not being used. Unplug the television from the power outlet when it will not be used for a long time or when there is an electrical storm. Never touch the antenna cable during a lightning storm. |  |
| Excessive volume from earphones and headphones can cause permanent hearing loss. Always monitor the volume of noise from these devices, especially when children are using them. |  |
Installation
 |
Ventilation should not be impeded or limited by covering the ventilation slots with items such as newspapers, tablecloths, curtains etc. At least 10cm of space should be left around the apparatus for sufficient ventilation. |
 |
The television should be situated away from heat sources such as radiators, heaters, stoves or other products that produce heat. Place the television in a position where the screen is not exposed to direct sunlight. It is best to have soft indirect lighting while watching and you should avoid a completely dark viewing environment and reflections to avoid eye fatigue. Keep the product away from high magnetic fields (such as near an amplifier speaker) to avoid affecting the tint. |
 |
Do not place the television on an unstable table, stand or shelf. The set may fall, causing serious injury as well as damage to the television itself. If moving the television on a cart, move the unit with care as sudden stops and starts may cause the television to overturn. |
 |
Do not place this television near water, for example near a bathtub, wash bowl, kitchen sink, laundry tub, swimming pool or in a damp basement etc. |
 |
When moving the television to a warm location from a cold location, allow some time for any dew or condensation inside the television to evaporate fully before you turn the unit on. |
 |
To prevent injury, the television must be securely attached to the floor/wall in accordance to the supplied installation instructions. |
Cleaning
|
Unplug the television from the power supply before cleaning. Do not use any liquid cleaners or harsh chemicals. Use a soft, damp cloth. |
 |
Safety & Warnings
Read all instructions before using the appliance and retain for reference.
- Unplug the monitor before cleaning it with a slightly damp, clean cloth.
- Wiping the screen once it has been turned off with a dry microfibre cloth is recommended.
- Do not use cleaning alcohol, ammonia-based liquids or other harsh cleaners.
- This monitor is designed with ventilation holes on the back of the casing. Do not cover or block them.
- Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking in adequate ventilation.
- Do not insert any objects or spray any liquids into the vents.
- Do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may injure nearby people.
- Unplug the monitor if it is not going to be used for an extended period of time.
- Do not place heavy objects on the monitor, its power cord or any connected cables.
- Do not open the back panel of the monitor, as it contains a high-voltage current even when not plugged in.
Overview
Monitor Controls
|
1. |
Menu: Press to display OSD menu and enter sub-menus |
4. |
Exit: Press to exit OSD menu |
|
2. |
Down: Press to move down in menus |
5. |
Power: Press to turn monitor on/off |
|
3. |
Up: Press to move up in menus |
6. |
LED Indicator: See above |
Note: Button 4 (E) can also switch between colour gamuts when a compatible graphics card and HDMI / DP connection are in use.
Indicator Light
- Solid blue/green/white light indicates power is on and monitor is operating normally.
- Flashing blue light indicates no video source has been detected.
- Red light indicates no signal detected or insufficient power received: check computer is set to send video output and that all cables are fully inserted and secure.
Monitor Ports
|
7. |
Power Input |
9. |
HDMI Input |
|
8. |
DisplayPort input |
10. |
HDMI Input |
Picture in Picture (PIP) Input
- PIP is supported with any secondary connection separate to the primary connection being used (e.g. secondary DP with primary HDMI ). The recommended configuration is 2x 1440p @144Hz.
Specifications
|
Screen Size |
27" |
Output |
Audio |
|
Curvature |
1800R |
Signal Input |
HDMI.DVI.DP |
|
Viewing Angle (H/V) |
178°/178° |
Power |
AC 100-240V.50/60HZ 1.5A |
|
Aspect Ratio |
16:9 |
OSD Language |
English, Chinese, Spanish, French, Dutch |
|
Resolution |
2560 x 1440 |
Environmental Temperature & Humidity |
Operating temperature: 0-40°C |
|
Backlight |
E-LED |
Storage temperature: -20~60°C |
|
|
Default Colour Temperature |
6500 |
Operating relative humidity: RH 10% to 85% (non-condensation) |
|
|
Typical Brightness |
MAX 250 |
Height Adjustment |
N/A |
|
Contrast Ratio |
3000:1 |
VESA Mounting |
With VESA additional bolt |
|
Dot Pitch |
0.2331(H)x0.2331(V)mm |
Response Time |
8ms |
|
Refresh Rate |
Up to 144hz |
|
|
System Requirements
| Operating System | Windows 7 / Windows 8 / Windows 10 64-bit or higher |
| Processor (CPU) | Intel Core i5 or AMD Phenom II X3 or higher |
| Graphics Card | NVIDIA GeForce GTX 950 or AMD Radeon R9 380 or higher |
| Memory | 6GB RAM |
Connectivity
Power Cable
Connect the included power cable to the monitor, then plug the other end into an AC outlet.
DisplayPort
Connect to this monitor from your compatible computer using a DisplayPort cable to receive a high-quality digital video signal.
HDMI
Connect to this monitor from your compatible computer using an HDMI cable (not included) to receive a high-quality digital video signal.
Stand Installation
1. Remove the monitor and protective packaging from the carton box carefully.
2. Take out the leg & support column and connect the two parts. (Use the KM4*14 screw supplied)
3. Take out the connection block by pressing the detach button. (Keep the monitor in its protective foam)
4. Attach the connection block to the support column and lock them. (Use 2x KM4*12 screws supplied)
5. Insert the connection block back into the rear of the monitor, then push down until firmly connected with the monitor.
6. Lift the monitor up straight and remove the protective foam.
Stand installation complete.
Wall Mounting
Note: this monitor only includes screws which may be used when attaching the monitor to a VESA 75*75mm wall mount.
1. Open the box, take out the product and protective foam attached, and gently place it on a desktop or table.
Remove the extra parts and the foam covering the back of the monitor. Press the release button to remove the stand plate. If the monitor was already attached to the stand, remove the stand.
2. Remove the original screws (x4) from the opening in the back of the monitor.
3. Follow the directions with your mount to install the monitor on the wall or fixture as desired. Remember to use the included 4 screws when mounting the monitor. Refer to image 2 below for correct screw placement.
Note: Do not discard the original screws. These may be needed for future use.
Operation
Setup
- For a basic setup, connect the monitor to your PC's graphics card using the included DisplayPort cable. An HDMI cable (not included) can be used instead.
- Connect the cable to the corresponding connector on your monitor as outlined in the Connectivity section of this user guide.
- Connect the power cable as outlined in the Connectivity section of this user guide.
- Press the power button on your monitor to turn it on.
OSD Menu
The On-Screen Display (OSD) menu can be used to adjust your monitor's settings.
When first connecting the monitor to your PC, settings will adjust automatically based on the configuration of your PC.
- Press any button to activate the navigation window.
- Press M to enter the OSD screen
3. Press Up or Down to browse functions and change
Press M to enter the sub-menu for a highlighted sub-menu
Press E to exit the current screen
List of functions:
|
Main Menu |
Sub-Menu |
Options |
Description |
|
Input Source |
DP |
NONE |
Switch to DP signal input |
|
HDMI-1 |
NONE |
Switch to HDMI 1 signal input |
|
|
HDMI-2 |
NONE |
Switch to HDMI 2 signal input |
|
|
Brightness/Contrast |
Brightness |
0-100 |
Adjust display brightness |
|
Contrast |
0-100 |
Adjust display contrast |
|
|
DCR |
On |
Turn on DCR function |
|
|
Off |
Turn off DCR function |
||
|
Colour Setting |
Gamma |
Gamma 2.0 |
Set the display Gamma add-in |
|
Gamma 2.2 |
|||
|
Gamma 2.4 |
|||
|
Picture Mode |
Standard, Text, Movie, Game, FPS, RTS |
Set a display preset |
|
|
Colour Temperature |
Warm, Cool, User |
Set the display colour temperature mode |
|
|
USER |
Red, Green, Blue |
Customize the display screen RGB component according to preference |
|
|
Low Blue Light |
0-100 |
Adjust blue light filtering level |
|
|
Hue/ Saturation |
Hue, Saturation |
Adjust display hue and saturation levels |
|
|
Picture Quality Setting |
Bypass |
On, Off |
Turn the bypass function on/off |
|
Sharpness |
0-100 |
Adjust display sharpness |
|
|
Response Time |
Off, High, Middle, Low |
Adjust display response time |
|
|
Noise Reduction |
Off, High, Middle, Low |
Reduce the interference of image noise caused by signal source interference |
|
|
Super- Resolution |
Off, High, Middle, Low |
When the resolution of the display screen is low, this function can be turned on to enhance the image resolution. |
|
|
Dynamic Luminous Control |
On, Off |
Compensate for grayscale display screen and strengthen the expression of grayscale |
|
|
FreeSync |
On, Off |
Turn the FreeSync function on/off |
|
|
Display |
Aspect Ratio |
Wide Screen, 4:3, Auto |
Select the on-screen aspect ratio |
|
DP Version |
DP 1.1, DP 1.2 |
Select DP version |
|
|
Audio |
Mute |
On, Off |
Turn mute mode on/off |
|
Volume |
0-100 |
Adjust audio volume |
|
|
Audio Source |
HDMI, DP |
Select audio signal input via HDMI or DP |
|
Main Menu |
Sub-Menu |
Options |
Description |
|
Multi-Window |
Multi-Window |
Off, PIP Mode, PBP 2Win |
Select PIP/PBP modes according to the number of input signals etc. |
|
Sub Win2 Input |
DP HDMI-1 HDMI-2 |
Select according to the input signal for PIP/ PBP mode |
|
|
PIP Size |
Small, Medium, Large |
Adjust the PIP/PBP window size |
|
|
PIP Position |
Top Right, Top Left, Bottom Right, Bottom Left |
Adjust the PIP/PBP window position |
|
|
Swap |
NONE |
Swap the PIP/PBP signal sources |
|
|
Other |
Language |
English, Espanol, |
Set OSD language |
|
OSD H-Position |
0-100 |
Adjust the OSD’s horizontal position |
|
|
OSD V-Position |
0-100 |
Adjust the OSD’s vertical position |
|
|
OSD Transparency |
0-100 |
Set the OSD’s overall transparency |
|
|
OSD Time Out |
5-100 |
Set how long the OSD remains open after non-use |
|
|
OSD Rotation |
Normal, 90,180, 270 |
When the user flips the display, this function can also flip the OSD to achieve the best display angle |
|
|
Reset |
|
Reset monitor configurations |
, 
Please Note: When choosing PIP/PBP function, make the default resolution in split screen mode 1920x1080 manually.
AMD FreeSync
If desired, you can use the monitor’s AMD FreeSync feature. The feature itself is on by default. In order to use this feature, please note you must have hardware with AMD FreeSync™ capability, a DisplayPort cable, and the latest graphics drivers. To use this feature, connect the appropriate cable to the DP connectors on both the computer and Monitor. After connecting, you will receive a prompt to enable the feature on your computer.
Gameplus
Press the up button in the OSD settings to toggle on-screen centre icons for FPS games or other scenarios.
Troubleshooting
|
Issue |
Possible cause / Steps to resolve |
|
Screen is blank |
Ensure power button has been pressed |
|
Check brightness/contrast |
|
|
Check indicator light; if flashing, no video signal is being received |
|
|
Check display settings of connected device |
|
|
Image out of focus |
Check video cable connection |
|
Screen is flashing |
An issue with the power source: contact Kogan.com |
|
Ensure devices which could cause magnetic disturbance (unshielded speakers, fluorescent lighting, AC transformers, etc.) are a safe distance away |
|
|
Colour bleeding, distortion or other unusual effects |
Check video cable connection |
|
Connect to another video source for comparison |
|
|
Inspect condition of ports on monitor and graphics card |
|
|
Adjust colour settings in monitor and PC display settings |
|
|
Screen strolling, rolling or moving |
Check source frequency is within 55-76HZ |
|
Check video cable connection |
|
|
Indicator light not illuminated |
Check power connection |
|
Check power has been turned on |
|
|
No video signal |
Confirm PC and graphics card compatibility |
|
Inspect condition of ports on monitor and graphics card |
|
|
Dim image |
Adjust brightness/contrast |
|
Image jitter/moire pattern |
Nearby electronic equipment may be causing interference |
|
The indicator is on or flashing but no image on the screen |
Confirm monitor has been turned on |
|
Confirm graphics card is installed |
|
|
Check video cable connection |
|
|
Inspect condition of ports on monitor and graphics card |
|
|
Check if PC is asleep or in standby, etc. |
|
|
Position or size incorrect |
Check settings in monitor OSD menu and PC display settings |