Kogan 2.0 Channel 40W Bluetooth Soundbar - (KASB40WSA) - Manual

Safety & Warnings

• Read all instructions before using the appliance and retain for reference.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• This appliance is designed for indoor household use: follow directions and use only as described.
• Do not use with an extension cord unless necessary, and if so, ensure it is suitably rated and it is handled safely as is the product's own power cord:
• Do not allow the power cord to be exposed to water, heat, direct sunlight or overhang where it can be pulled or otherwise be damaged or pose a hazard.
• This equipment is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience or knowledge. They should be given appropriate supervision and instructions to use the equipment by a person responsible for their safety.
• Do not immerse the product in water or any other liquid.
• Always unplug the appliance after use and before any cleaning or user maintenance.
• Always unplug from power by pulling the plug and not the power cord.
• Ensure the equipment is not too close to heat emitting appliances or placed in direct sunlight.
• To reduce the risk of electric shock, do not remove cover.
• Do not push objects into any openings as damage to the equipment and/or electric shock may occur.
• This appliance contains no user-serviceable parts. If it suffers any failure or damage, cease usage and contact Kogan Support after consulting the Troubleshooting section of this manual.

Overview

Controls

1. SOURCE/6: Power on, function change (short press), power off (long press)
2. VOL: +
3. VOL-
4. PAIR: Short or long press to enter Bluetooth pairing mode
5. LINE IN
6. AUX IN (L/R)
7. OPTICAL IN
8. DC IN
9. HDMI IN

Function Indicator LEDs

1. Red LED light: Illuminated when device is in standby and turns off when device is turned on.
2. Green LED light: Indicates LINE IN or AUX IN function
3. Orange LED light: Indicates Optical function
4. White LED light: Indicates HDMI function
5. Blue LED light: Slow blinking when Bluetooth not connected, flashing while pairing and solid while connected

Remote

The remote control takes 2 AAA batteries and has a range of approximately 6 metres.

1. :Power
2. TREBLE+: Raise treble level, short press to unmute (except in Movie mode)
3. TREBLE-: Lower treble level, short press to unmute (except in Movie mode)
4. : Previous track in Bluetooth mode
5. : Press to jump next song in Bluetooth mode
6: VOL+: Raise volume, short press to unmute
7: VOL -: Lower volume, short press to unmute
8. : Play/pause music in Bluetooth mode, short press to unmute
9. MUSIC: Music EQ mode
10. MOVIE: Movie EQ mode (cannot adjust bass/treble)
11. DIALOGUE: Dialogue EQ mode
12. BASS +: Raise bass level, short press to unmute (except in
Movie mode)
13. BASS -: Lower bass level, short press to unmute (except in
Movie mode)
14. : Short press to change between HDMI/OPTICAL IN/LINE
IN/AUX IN mode, long press to toggle mute on/off

Specifications

Specifications and design subject to change without notice.

Operation

Setup

1. Connect an audio source to soundbar’s Line In / Aux In / Optical / HDMI port.
2. Connect the supplied power adaptor to the soundbar: the standby light will come on red.
3. Turn the soundbar on with the remote. On first use, the Bluetooth mode will be set. When powering on subsequently, it will be in the last mode used.
4. Set a source: short press the power button (device) or mode (remote) to cycle through. The colour of the indicator light will change to display the set mode.

Bluetooth Paring

1. Short press mode on the remote control or Source on the soundbar to enter Bluetooth mode.
2. The indicator light will slowly flash blue. Press PAIR on unit into Bluetooth pairing mode and the blue indicator light will blink quickly.
3. Turn on Bluetooth in your device settings, locate KASB40WSA and connect to it. If prompted for a password, enter ”0000”.
4. When successfully paired, the indicator light will be solid.
5. Press PAIR on the unit to disconnect and re-enter pairing mode.

Note: The operation range for the Bluetooth connection is approximately 10 meters in ideal conditions with no obstructions, etc..
Note: If a mobile phone you are playing music from receives a call, the music will be interrupted. Call audio will not play through the soundbar. Once the call is ended, music playback will resume through the soundbar.

Optical / AUX / Line In / HDMI

1. Connect the audio source to the soundbar using the appropriate cable.Ensure that the soundbar is connected to the TV or other audio device via optical cables.
2. Set a source: short press the source button (device) or mode (remote) to cycle through. The colour of the indicator light will change to display the set mode.

Note: The playback is controlled by your device and by the buttons on the remote control and the soundbar.
Note: On HDMI source, the soundbar can synchronise volume with the TV.
Note: If no sound is coming out of the soundbar, make sure the audio setting of your source player,(e.g DVD player, game player, TV) is set to PCM with optical output.

Troubleshooting