Safety & Warnings
Handle with care and inspect regularly to ensure product is in good working order. If this product, power supply cord or plug shows any signs of damage: stop use, unplug the product and contact Kogan.com support. |
General Safety Instructions
Risk of electric shock. DO NOT OPEN! Do not attempt to service the television yourself, as opening or removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to the Kogan customer support team. |
![]() |
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The television should not be exposed to dripping or splashing and no liquid filled objects such as vases should be placed on the case. |
![]() |
In the event of smoke, strange noises or a strange smell from the unit, you should follow these steps:
|
![]() |
Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill any liquids onto the set. Use special caution in households where children are present. The television is not suitable for children under 4 years old to operate. | ![]() |
Power supply cords should be routed safely to prevent dangers due to damaged cords. The mains plug is the main disconnect method, so it should be easily accessible and not be obstructed during use. |
![]() |
To avoid fires, no naked flame sources such as lit candles or burning incense should be placed onto the casing of the television. | ![]() |
Do not pull the plug out of a power outlet by pulling on the power cable. Always grasp the plug and pull. Never touch the plug with wet hands. | ![]() |
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal. | ![]() |
Always turn the set off when it is not being used. Unplug the television from the power outlet when it will not be used for a long time or when there is an electrical storm. Never touch the antenna cable during a lightning storm. | ![]() |
Excessive volume from earphones and headphones can cause permanent hearing loss. Always monitor the volume of noise from these devices, especially when children are using them. | ![]() |
Installation
![]() |
Ventilation should not be impeded or limited by covering the ventilation slots with items such as newspapers, tablecloths, curtains etc. At least 10cm of space should be left around the apparatus for sufficient ventilation. |
![]() |
The television should be situated away from heat sources such as radiators, heaters, stoves or other products that produce heat. Place the television in a position where the screen is not exposed to direct sunlight. It is best to have soft indirect lighting while watching and you should avoid a completely dark viewing environment and reflections to avoid eye fatigue. Keep the product away from high magnetic fields (such as near an amplifier speaker) to avoid affecting the tint. |
![]() |
Do not place the television on an unstable table, stand or shelf. The set may fall, causing serious injury as well as damage to the television itself. If moving the television on a cart, move the unit with care as sudden stops and starts may cause the television to overturn. |
![]() |
Do not place this television near water, for example near a bathtub, wash bowl, kitchen sink, laundry tub, swimming pool or in a damp basement etc. |
![]() |
When moving the television to a warm location from a cold location, allow some time for any dew or condensation inside the television to evaporate fully before you turn the unit on. |
![]() |
To prevent injury, the television must be securely attached to the floor/wall in accordance to the supplied installation instructions. |
Cleaning
Unplug the television from the power supply before cleaning. Do not use any liquid cleaners or harsh chemicals. Use a soft, damp cloth. |
![]() |
Important Safety Precautions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the I manufacturer, or sold with the apparatus. When a cart is used caution when moving the cart/apparatus combination to avoid injury tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Warning to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
15. The apparatus shall be disconnected from the mains by placing the power/standby switch in the standby position and unplugging the power cord of the apparatus from the AC mains receptacle.
16. The socket-out shall be installed near the equipment and shall be easily accessible.
17. This product should never be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
18. Apparatus shall not be exposed to dripping or splashing.
19. Do not place any sources of danger on the apparatus (e.g. liquid filled objects, lighted candles).
20. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
21. Never place the TV, remote control or batteries near naked flames or other I heat sources, including direct sunlight. To prevent the spread of fire, keep ‘ candles or other flames away from the TV, remote control and batteries at all times.
22. The USB terminal should be loaded with 0.5 A under normal operation.
TV Bracket assemble
Fix the TV on the wall
1. First, put the TV on the table smoothly and put some soft cloth on the table to avoid scratching the screen.
2. User the screw driver to take off the screws which are fixed on the bottom stand (the direction of the arrow, refer to the ptoto1). And take off the bottom stand (please take off the screws and bottom stand carefully).
3. Make one bracket which can fix on the wall according to the size of arrow direction of photo2 and photo3.
4. Drill four holes properly on the wall (the size only for reference) and put into four screws.(optional parts) Drill four holes properly on the wall (the size only for reference) and put into four screws.(optional parts)
5. according to the step 4,use the screwdriver to lock the screw on the back of the TV. then hang the TV on the wall.
Note:
1. The bracket fixed on the wall is optional part.
2. when you assemble the TV, there should be no other articles on the around and front and please keep the distance from other articles.
3. When assemble the TV, please ask the career man to fix in order to avoid the danger.
4. The fixing picture is only for reference.
5. Please follow the use manual about bracket assemble to fix the TV.
6. Attach the mounting bracket from the VESA compatible wall mounting kit.
TV Buttons And Terminal Interface
TV Buttons
Note: The following is only functional schematic, And the actual position and arrangement of different models may be different.
: Turn ON/OFF Power.
SOURCE: External Signal Input Selection.
MENU: Display Main MENU And Confirm MENU Item Selection.
CH+/-: Selecting Channel.
VOL+/-: Adjusting Volume.
Terminal Interface
Note: The following are the various terminal interface, the actual position and arrangement, the number of different models may be different.
![]() |
AV input External AV Signal Input And Relevant Right/Left Sound Channel |
![]() |
EARPHONE output When earphones are plugged in, speakers are disabled |
![]() |
USB input Connect a USB device here to play its media files or to record programs via the PVR function. |
![]() |
COAXIAL output Connect the SPDIF receiver. |
![]() |
Y Pb Pr input Connect to the composite terminal of your DVD/VCR (Some models without this interface) |
||
![]() |
HDMI input Digital signal input from HDMI video connector. |
||
![]() |
ANT 75 Connect the antenna/cable TV input (75/VHF/UHF) |
||
![]() |
VGA input PC analog signal input |
||
![]() |
PC AUDIO INPUT VGA input and audio input when VGA input |
External device connection diagram
Install And Connect TV
![]() |
Set your TV To put your TV in a firm place which can bear the weight of the TV. To avoid danger, please don't expose the TV near water or heating place (such as light, candle, heating machine),do not block the ventilation at the back of TV. |
![]() |
Connect antenna and power 1. Connect the antenna cable to the antenna socket on the back of the TV. 2. To plug the power cord of TV (AC 100- 240V~ 50/60Hz). |
Turn on TV Note: |
TV Stand Installation Instructions
1. Turn over the TV, and the LED side should be on the smooth plane. Be sure no foreign matter on the plane.
2. Take out all the screws and base.
3. Fix base with 4pcs screws(BM4*10).
TV Menu
Input Source
Note: The above is for reference only, to prevail any kind
Press INPUT button to display the input source list,
Press ▼/▲ or INPUT button to select the input source you want to,
Press ENTER button to enter the input source,
Press EXIT button to quit.
Picture Menu
Press MENU button to display the main menu.
Press ◄/► button select PICTURE in the main menu,then press ENTER/▼ to enter.
1. Press ▼/▲ button to select the option that you want to adjust in the PICTURE menu.
2. Press Enter/◄/► button to adjust.
3. After finishing your adjustment, Press MENU button to save and return back to the previous menu.
Picture MODE
Press ▼/▲ button to select Picture Mode, then press ◄/► button to select.
TIPS: You can press PMODE button to change the Picture Mode directly.
Brightness/Contrast/Sharpness/Saturation/Hue
Press ◄/► button to select option, then press ◄/► button to adjust.
Brightness: Adjust the optical fiber output of the entire picture, it will effect the dark region of the picture.
Contrast: Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.
Sharpness: Adjust the peaking in the detail of the picture.
Saturation: Adjust the saturation of the color based on your own like.
Hue: Use in compensating color changed with the transmission in the NTSC code.
Color Temp
Change the overall color cast of the picture.
Press ▼/▲ button to select Color Temp, then press ◄/► button to select Standard/Cool/Warm.
Standard: Produces a vivid image.
Cool: Produces a gentle blue-hued image.
Warm: Produces a red-hued image.
Aspect Ratio
Press ▼/▲ button to select Aspect Ratio, then press ◄/► button to select.
Auto: Automatically adjust Aspect Ratio based on TV size and TV program.
Full/4:3 /Zoom1/Zoom2 To select the available display format.
PC Setting
Press INPUT to select PC source.
Press MENU to enter the main menu,then press ◄/►button to select PICTURE menu.
Press ENTER/▼ to enter and press ▼ to select PC Setting.
Advanced Settings
Adjust advanced video features to fine tune the picture.
Press ▼/▲ button to select Advanced Settings, then press Enter/► button to enter sub-menu.
Sound Menu
Press MENU button to display the main menu.
Press ◄/► button select SOUND in the main menu, then press ENTER/▼ to enter.
1. Press ▼/▲ button to select the option that you want to adjust in the SOUND menu.
2. Press Enter/◄/► button to adjust.
3. After finishing your adjustment, Press MENU button to save and return back to the previous menu.
Sound Mode
Press ▼/▲ button to select Sound Mode, then press ◄/► button to select.
Treble/Bass/Balance
Press ▼ / ▲ button to select option, then press ◄/► button to adjust.
Treble: Adjust the treble effect. Increases or decreases high-pitched sounds.
Bass: Adjust the bass effect. Increases or decreases lower-pitched sounds.
Balance: Adjust the balance between left and right speakers to adapt to your listening position.
Surround Sound
Press ▼/▲ button to select Surround Sound, then press ◄/► button to select On or Off.
EQ Setting
Adjust the curve of 7 bands equalizer.
Press ▼/▲ button to select EQ Setting , then press Enter/► button to enter sub-menu.
AVL
Set the auto volume control.
Press ▼/▲ button to select AVL, then press ◄/► button to select On or Off.
SPDIF
Press ◄/► button to select SPDIF, then press ◄/► button to select Off / Auto / PCM.
Audio Description
Press ▼/▲ button to select Audio Description , then press Enter/► button to enter sub-menu.
Sound Type
Press ▼/▲ button to select Sound Type, then press ◄/► button to select. (Available Sound Type: Stereo, Dual I, Dual II, Mixed).
Channel Menu
Press MENU button to display the main menu.
Press ◄/► button to select CHANNEL in the main menu, then press ENTER/▼ to enter.
1. Press ▼/▲ button to select the option that you want to select in the CHANNEL menu.
2. Press ENTER button to enter sub-menu.
3. Press MENU button to return back to the previous menu.
Auto Scan
Press ▼/▲ button to select Auto Scan , then press Enter/► button to enter sub-menu.
Manual Scan
Press ▼/▲ button to select Manual Scan , then press Enter/ ► button to enter sub-menu.
Digital Manual Scan
Press ▼/▲ button to select Digital Manual Scan, then press Enter/ ► button to enter sub-menu.
Analog Manual Scan
Press ▼/▲ button to select Analog Manual Scan, then press Enter/► button to enter sub-menu.
Analog Scan
Press ◄/► button to select Analog Scan.
Color System
Press ◄/► button to select Color System: Auto, PAL or SECAM.
Sound System
Press ◄/► button to select Sound System: Auto, DK, BG, I or L.
Modulation
Press ◄/► button to select Modulation: Auto, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM.
AFC
Automatic Fine tuning.
press 4 / Hbutton to select On or Off.
Start
Press Enter/►button to start the channel searching.
Channel Edit
Press ▼/▲ button to select Channel Edit, then press Enter/► button to enter sub-menu.
The three colored key is the shortcut key for programming the channel.
First press ▼/▲ to highlight the channel you want to delete or move or skip, then:
Press the Red button to delete the channel.
Press the Green button to skip the select channel. (Your TV set will skip the channel automatically when using CH+/- to view the channels.)
Press the Blue button to to set the channel to moving state. then press ▼/▲ to move it to the position you want to put.
Signal Information
Press ▼/▲ button to select Signal Information, then press the Enter button to see the detail information about the signal. Only available under DTV mode.
Lock System Menu
Press MENU button to display the main menu.
Press ◄/► button select Lock System in the main menu, then press ENTER/▼ to enter.
1. Press ▼/▲ button to select the option that you want to adjust in the Lock System menu.
2. Press Enter/◄/► button to adjust.
3. After finishing your adjustment, Press MENU button to save and return back to the previous menu.
Default password is 0000,and if forget what you set, please call the service center.
Press ▼/▲ button to select Enable then press ◄/► button to select On or Off.
Channel Locks, Parental Rating and Lock Keypad are available when Enable is On.
Channel Locks
Press ▼/▲ button to select Channel Locks, then press Enter/► button to enter sub-menu.
Parental Rating
Press ▼/▲ button to select Parental Rating, then press ◄/► button to select.
Lock Keypad
Set to prevent it from being used by young children, or other unexpected usage.
Press ▼/▲ button to select Lock Keypad, then press ◄/► button to select On or Off.
New Password
Press ▼/▲ button to select New Password, then enter a 4-digital number you want to set twice.
Setup Menu
Press MENU button to display the main menu.
Press ◄/► button select SETUP in the main menu, then press ENTER/▼ to enter.
1. Press ▼/▲ button to select the option that you want to adjust in the SETUP menu.
2. Press Enter/ ◄/► button to adjust.
3. After finishing your adjustment, Press MENU button to save and return back to the previous menu.
OSD Language
Press ▼/▲ button to select OSD Language, then press ◄/► button to select.
Audio Languages
Press ▼/▲ button to select Audio Languages, then press Enter button to enter sub-menu.
Press ▼/▲ / ◄/► button to select the Audio Primary Language and Audio Secondary Language.
Subtitle
Press ▼/▲ button to select Subtitle, then press Enter button to enter sub-menu.
Teletext
Adjust Teletext settings. Only available under DTV and ATV source. Press ▼/▲ button to select Teletext , then press Enter/►button to enter sub-menu.
Mode Setting
Press ▼/▲ button to select Mode Setting.
Time Settings
Press ▼/▲ button to select Time Settings, then press Enter/► button to enter sub-menu.
PVR Settings
Press ▼/▲ button to select PVR Settings, then press Enter button to enter sub-menu.
It will check the USB.
First Time Setup
Press ▼/▲ button to select First time Setup, then press Enter button to enter.
OAD
Press ▼/▲ button to select OAD, then press Enter button to enter sub-menu.
Reset
Press ▼ / ▲ button to select Reset, then press Enter button to enter sub-menu.
USB Operation
Note: Before operating USB menu, plug in USB device, then press INPUT button to set the Input Source to USB.
Press ◄/► button to select USB in the Source menu, then press Enter button to enter.
Press ◄/► button to select the option you want to adjust in the main USB menu, then press Enter button to enter.
Help
No Power |
Check the AC cord of TV is plus in or not. If still no power, please pull out the plug and re-plug in after 60 seconds. And open the TV again |
Signal receive not properly |
• To cause double image or phantom if there has high building or high mountain round TV. You can adjust image effect by manually operation: consult instruction of vernier regulation or change the direction of external antenna. • If you use the indoor antenna . under certain circumstance, receive will be more difficult .So you can change the direction of the antenna to adjust the image effect. If can't change image receiving effect either, you have to use external antenna. |
No picture |
• Check the antenna at the back of TV is connected properly or not. • Try to select other channels and check whether the TV problem itself or not |
Video is ok without audio |
• Increase the volume. • Check the TV is in mute mode or not, and please press the mute button to make sound resume. |
Audio is ok, but color error or no picture. |
• Increase contrast and brightness. |
Snow Statics Picture and Noise |
• Check the antenna at the back of TV is connected or not. |
Level broken line |
• Vacuum, such as hair drier, Maybe has electrical appliance interfere- please turn off these kinds of electrical appliance, cleaner and so on. |
Image or-Dual "simulacrum" The TV no response with the Remote. |
• Perhaps the location for the antenna is not good. Use the tall beamed antenna can be improved quality of the display image. • Operate the remote direct to the remote sensor on the TV. If still no response for the TV, please check if the plastic bag on the remote take or not. And check if the location for the battery is correct.Change the new battery. • The TV will shift to the STAND BY if no response from the remote in the few minutes. |
NO Video In (PC Mode) |
• Please check if the display cable connect to the VGA correct. • Please check if there has the bend on the display cable. |
Vertical Twinkling (PC Mode) |
• Enter the main menu, Use the clock regulator for the Video display noise to eliminate the vertical line. |
Horizontal Ripping (PC Mode) |
• Adjust the Audio sound horizontal in the main menu to clear the horizontal ripping line. |
The screen is too bright or too dark (PC Mode) |
• Adjust the contrast ratio or brightness in the main menu. |
PC Function no response |
• Check the computer setting in the state of compatible display resolution |
Ripping line in RCA connecting |
• Please use good quality connecting cable. |
Problem still exist |
• Unplug the power cable and wait for 30 seconds, then connect. If there is some problem with our TV, do not repair it by yourself, please contact with the customer service center. |
There will be complete picture and the brightness will come down if the TV is in: Note So please do not keep the TV in a state of same, the static picture for too long time Menu or same picture that has much difference in brightness and contrast ratio for too long time.
Machine Technical Specifications
Screen Size |
24" |
Viewing angle |
178° (Horizontal) / 178° (Vertical) |
TV system |
PAL/SECAM |
Video system |
PAL/NTSC |
Preset Channels |
ATV:99 DTV:1200 |
Input/Output |
IN TV, AV, Y Pb Pr, PC, HDMI, USB OUT EARPHONE, COAXIAL |
Speaker Output |
5W+5W |
Power requirement |
DC 12V |
Power consumption |
36W |
Accessories |
Remote controller, warranty card Quick Setup Guide, 2xAAA Batteries |
NOTE:
This user manual is for reference only. Specifications are subject to change without notice.
Remote Controller
1. POWER: Set your TV to power on or standby mode.
2. MUTE: Press to mute the sound. Press again or press VOL+ to unmute.
3. 0-9: Press 0-9 to select a TV channel directly while watching TV. The channel will change after 2 seconds. Applicable for entering page number in teletext mode and so on.
4. DTV/ATV: Switch between Analog and Digital TV
5. Return to the previous viewed program.
6. S.MODE: Press to cycle through the different sound settings
7. SLEEP: Select amount of time before TV turn itself off automatically.
8. MTS: Press to search the NICAM modes.
9. P.MODE: Press to cycle through the different picture settings
10. MENU: Allow you to navigate the on-screen menus.
11. SOURCE: Open the main menu .press to list the sources
12. ▼▲ ◄► ENTER: Allow you to navigate the on-screen menus and adjust the system settings to your preference.
13. EXIT: Exit from the menu or sub-menu and cancel the function in process (if applicable)
14. DISPLAY: Press to display the source and channel's info.
15. VOL+/VOL-: Press to increase I decrease the sound level.
16. TV/RADIO : When watching channel, allows you to switch between TV and Radio modes
17. GUIDE: 1. Launches the EPG (Electronic Program Guide) 2. Fast reverse in PVR or Media Player mode.
18. TIME SHIFT: 1.DTV channel time shift Function. 2.play on PVR or Media Player mode.
19. CANCEL: 1. When a page is selected in the mode of text, it may take some time before it becomes available, pressing the CANCEL key will return to the TV mode. When the required page is found , the page number will appear at the top of the TV picture, press the CANCEL key to return to the mode of text for you to browse this page. 2. Previous chapter in PVR or Media Player mode
20. INDEX: 1. Request the Index page in Teletext mode. 2.Exit the playing function in PVR or Media Player mode.
21. SIZE: Change the size of display in Teletext mode.
22. REVEAL: Reveal or Hide the hidden words.
23. COLOR BUTTONS: Teletex switch of the analog parts, the items selection in the menu of the digital parts and the practice of the MHEG5 in the DVB menu.
24. CH+/CH-: Press to scan through channels.
25. FAV/LIST: press to open the favorite list, then you can select the favorite channel.
26. ASPECT: 1. Select picture scale. 2.fast forward in PVR or Media Player mode.
27. FREEZE: press to freeze the picture
28. SUB.PG: 1. Press to access sub page.2. Next chapter in PVR or Media Player mode.
29. SUBTITLE: To show and set the language of current DTV.
30. HOLD: HOLD On or Off for current page display.
31. TEXT: Switch the teletext on and off.
32. RECLIST: Show the recorded list.
33. REC: Record begin in PVR mode.
Battery Installation:
Remove the battery compartment lid on the rear of the remote control by sliding the lid down, then off. Put two AAA batteries inside the battery compartment with their + and - ends aligned as indicated. Do not mix old and new batteries or different types of batteries. Slide the lid until you hear it click into place.
Using the Remote Control:
Unless stated, otherwise, the remote control can operate all the features of the TV.
Always point the remote control directly at the remote sensor in front of the TV.