Kogan 40" Full HD LED TV (Series 7 GF7000) - (KALED40GF7000RA) - Manual

Safety & Warnings

Handle with care and inspect regularly to ensure product is in good working order. If this product, power supply cord or plug shows any signs of damage: stop use, unplug the product and contact Kogan.com support.

 

General Safety Instructions

Risk of electric shock. DO NOT OPEN! Do not attempt to service the television yourself, as opening or removing the covers may expose you to dangerous voltage or other hazards. Refer all servicing to the Kogan customer support team.
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. The television should not be exposed to dripping or splashing and no liquid filled objects such as vases should be placed on the case.
In the event of smoke, strange noises or a strange smell from the unit, you should follow these steps: Turn off the unit immediately. Disconnect the power plug from the power outlet. Contact the Kogan customer support team. Never attempt to make repairs yourself.
Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short-circuit parts that could result in a fire or electric shock. Never spill any liquids onto the set. Use special caution in households where children are present. The television is not suitable for children under 4 years old to operate.
Power supply cords should be routed safely to prevent dangers due to damaged cords. The mains plug is the main disconnect method, so it should be easily accessible and not be obstructed during use.
To avoid fires, no naked flame sources such as lit candles or burning incense should be placed onto the casing of the television.
Do not pull the plug out of a power outlet by pulling on the power cable. Always grasp the plug and pull. Never touch the plug with wet hands.
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them may be fatal.
Always turn the set off when it is not being used. Unplug the television from the power outlet when it will not be used for a long time or when there is an electrical storm. Never touch the antenna cable during a lightning storm.
Excessive volume from earphones and headphones can cause permanent hearing loss. Always monitor the volume of noise from these devices, especially when children are using them.

 

Installation

	Ventilation should not be impeded or limited by covering the ventilation slots with items such as newspapers, tablecloths, curtains etc. At least 10cm of space should be left around the apparatus for sufficient ventilation.
	The television should be situated away from heat sources such as radiators, heaters, stoves or other products that produce heat. Place the television in a position where the screen is not exposed to direct sunlight. It is best to have soft indirect lighting while watching and you should avoid a completely dark viewing environment and reflections to avoid eye fatigue. Keep the product away from high magnetic fields (such as near an amplifier speaker) to avoid affecting the tint.
	Do not place the television on an unstable table, stand or shelf. The set may fall, causing serious injury as well as damage to the television itself. If moving the television on a cart, move the unit with care as sudden stops and starts may cause the television to overturn.
	Do not place this television near water, for example near a bathtub, wash bowl, kitchen sink, laundry tub, swimming pool or in a damp basement etc.
	When moving the television to a warm location from a cold location, allow some time for any dew or condensation inside the television to evaporate fully before you turn the unit on.
	To prevent injury, the television must be securely attached to the floor/wall in accordance to the supplied installation instructions.

 

Cleaning

Unplug the television from the power supply before cleaning. Do not use any liquid cleaners or harsh chemicals. Use a soft, damp cloth.

 

Specifications 

Speakers	2 x 8W
HDMI	1.4
HDMI-CEC	Yes
USB	1 x USB 2.0
VESA Wall Mount Pattern	200 x 200 | M6 Screw
Weight	6.7kg
Without Stand	910.84 x 521.8 x 94.6mm
With Stand	910.84 x 567.05 x 211.45mm
Brightness	220 cd/m2
Colours	16.7M
Computer Supported Resolutions	640x480 @ 60Hz, 800x600 @ 60Hz, 1024x768 @ 60Hz, 1360X768 @ 60Hz,HDMI support 1920X1080 @ 60Hz
Contrast Ratio	5000:1
Native Aspect Ratio	16:9
Panel Manufacturer	Innolux
Refresh Rate	60 Hz
Resolution	1920 x 1080
Response Time	8.5 ms
Size	40"
Viewing Angle	178 / 178
HDCP	1.2
TV Features	VESA Mount Compatible
TV Features	PVR
TV Resolution	Full HD 1080p
Component (YPbPr)	1
Composite (AV)	1
HDMI	3
PC Audio	1
VGA (D-sub)	1
3.5mm Stereo Audio	1
Optical Audio Out	1
Average Consumption	60 W
Energy Consumption	144 kWh per year
Energy Rating	6.0 Star
Standby Consumption	< 1 W
Tuner Type	DVB-T/T2

 

Accessories

Remote controller
Power cord
AAA Batteries

TV Bracket assemble

Fix the TV on the wall

1. First, put the TV on the table smoothly and put some soft cloth on the table to avoid scratching the screen.
2. User the screw driver to take off the screws which are fixed on the bottom stand (the direction of the arrow, refer to the photo 1). And take off the bottom stand(please take off the screws and bottom stand carefully).
3. Make one bracket which can fix on the wall according to the size of arrow direction of photo 2 and photo 3.
4. Drill four holes properly on the wall (the size only for reference) and put into four screws.(optional parts) Drill four holes properly on the wall (the size only for reference) and put into four screws.(optional parts)
5. According to the step 4, use the screwdriver to lock the screw on the back of the TV, then hang the TV on the wall.

Note:

1. The bracket fixed on the wall is optional an part.
2. When you assemble the TV, there should be no other articles on the around and front and please keep the distance from other articles.
3. When assemble the TV, please ask the career man to fix in order to avoid the danger.
4. The fixing picture is only for reference.
5. Please follow the use manual about bracket assemble to fix the TV.
6. Attach the mounting bracket from the VESA compatible wall mounting kit.

Remote

TV Buttons And Terminal Interface

TV Buttons

Note: The following is only functional schematic, And the actual position and arrangement of different models may be different.

            

: Turn ON/OFF Power.
SOURCE:    External Signal Input Selection.
MENU:        Display Main MENU And Confirm MENU Item Selection.
CH+/-:        Selecting Channel.
VOL+/-:      Adjusting Volume.

Terminal Interface

Note: The following are the various terminal interface, the actual position and arrangement, the number of different models may be different.

	AV input External AV Signal Input And Relevant Right/Left Sound Channel		EARPHONE output When earphones are plugged in, speakers are disabled
	AV output External AV Signal output And Relevant Right/Left Sound Channel (Some models without this interface)		USB input only for software upgrade.
	Y Pb Pr input Connect to the composite terminal of your DVD/VCR (Some models without this interface)		COAXIAL output Connect the SPDIF receiver.
	HDMI input Digital signal input from HDMI video connector.		LINE output Audio Out R/L
	ANT 75 Connect the antenna/cable TV input (75/VHF/UHF)
	VGA input PC analog signal input
	PC AUDIO INPUT VGA input and audio input when VGA input

 

External device connection diagram

Install And Connect TV

Set your TV To put your TV in a firm place which can bear the weight of the TV. To avoid danger, please don’t expose the TV near water or heating place (such as light, candle, heating machine),do not block the ventilation at the back of TV. Connect antenna and power Connect the antenna cable to the antenna socket on the back of the TV. To plug the power cord of TV (AC 100-240V~ 50/60Hz). Turn on TV Press the power button of the TV the indication light will turn to green. if it is on standby mode (the light is red), press the power button on the remote control to turn on the TV. Note: Picture for reference purposes only.

 

TV Stand Installation Instructions

Open the carton and remove the TV and scattered accessories and base (some models without base). To avoid the injury of the TV, covered with a soft mattress, put it on the table, face down on a soft mattress, the base of the neck is fixed on the TV with screws. Screw the base and connected to the TV. The installation is complete.

Note:
Picture for reference purposes only.
Please prevail in kind.

DTV Menu

Picture Menu

Press MENU button to display the main menu.
Press ◄ / ► button select PICTURE in the main menu, then press ENTER / ▼ to enter.

1. Press ▼ / ▲ button to select the option that you want to adjust in the PICTURE menu.
2. Press Enter/◄ / ► button to adjust.
3. After finishing your adjustment, Press MENU button to return back to the previous menu.

Sound Menu

Press MENU button to display the main menu.
Press ◄ / ► button select SOUND in the main menu, then press ENTER / ▼ to enter.

1. Press ▼ / ▲ button to select the option that you want to adjust in the SOUND menu.
2. Press Enter/◄ / ► button to adjust.
3. After finishing your adjustment, Press MENU button to return back to the previous menu.

Picture MODE

Press ▼ / ▲ button to select Picture Mode, then press◄ / ► button to select.
TIPS: You can press PMODE button to change the Picture Mode directly.

Brightness/Contrast/ Sharpness/Saturation/Hue
Press ▼ / ▲ button to select option, then press ◄ / ► button to adjust.
Brightness  Adjust the visual perception output of the entire picture, it will effect the luminousness of the picture.
Contrast      Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.
Sharpness  Adjust the peaking in the detail of the picture.
Saturation   Adjust the saturation of the color based on your own like.
Hue             Use in compensating color changed with the transmission in the NTSC mode.

Color Temp
Change the overall color cast of the picture.
Press ▼ / ▲ button to select Color Temp, then press◄ / ► button to select Standard/Cool/Warm.
Standard   Produces a vivid image.
Cool          Produces a gentle blue-hued image.
Warm        Produces a red-hued image.

Aspect Ratio

Press ▼ / ▲ button to select Aspect Ratio, then press◄ / ► button to select.
Full/4: 3 /Zoom1/Zoom2 to select the available display format.

Advanced Settings

Adjust advanced video features to fine tune the picture.
Press ▼ / ▲ button to select Advanced Settings, then press Enter / ► button to enter sub-menu.

NR

Set options to reduce video noise.
Press ▼ / ▲ button to select NR, then press◄ / ► button to select.

Off            Select to turn off video noise detection.
Weak        Detect and reduce low video noise.
Medium    Detect and reduce moderate video noise.
Strong      Detect and reduce enhanced video noise.

Dynamic Contrast

Automatically adjust picture detail and brightness.
Press ▼ / ▲ button to select Dynamic Contrast then press ◄ / ► button to select.

Sound Mode
Press ▼ / ▲ button to select Audio Mode, then press◄ / ► button to select.
TIPS: You can press SMODE button on the remote control to change the Sound Mode directly.

Standard      Produces a balanced sound in all environments.
Music           Preserves the original sound.Good for musical programs.
Personal      Select to customize picture settings.
Movie           Enhances treble and bass for a rich sound experience.

Treble/Bass/Balance
Press ▼ / ▲ button to select option, then press ◄ / ► button to adjust.
Treble        Adjust the treble effect.Increases or decreases high-pitched sounds.
Bass          Adjust the bass effect.Increases or decreases lower-pitched sounds.
Balance    Adjust the balance between left and right speakers to adapt to your listening position.

Surround Sound
Press ▼ / ▲ button to select Surround Sound, then press◄ / ► button to select On or Off.

EQ Setting
Adjust the curve of 7 bands equalizer
Press ▼ / ▲ button to select EQ Setting, then press Enter / ►button to enter sub-menu.

AVL
Automatically reduces sudden volume changes,for example,when switching beween the channels.
Press ▼ / ▲ button to select AVL, then press◄ / ► button to select On or Off.
SPDIF
Press ▼ / ▲ button to select Digital Output, then press ◄ / ► button to select Off / Auto/PCM.

Audio Description
Press ▼ / ▲ button to select Audio Description, then press Enter / ► button to enter sub-menu.

Mode
Press ▼ / ▲ button to select Mode, then press◄ / ► button to select On or Off.
When the mode is On, Volume can be adjust by users.

Sound Type
Press ▼ / ▲ button to select Sound Type, then press◄ / ► button to select.

NOTE:

Balance: This item can adjust the speaker’s output, it enables you to listen to best at your position.
AVL: This item uses for reducing the difference between channel and program’s volume automatically.
It made the overall water to be even. This function will also reduce the fluctuation of the sound.

Channel Menu

Press MENU button to display the main menu.
Press ◄ / ► button to select CHANNEL in the main menu, then press ENTER / ▼ to enter.

1. Press ▼ / ▲ button to select the option that you want to select in the CHANNEL menu.
2. Press Enter button to enter sub-menu.
3. Press MENU button to return back to the previous menu.

Tuner Type
Press ▼ / ▲ button to select Tuner Type, then press ◄ / ► button to select Antenna or Cable.

Auto Scan
Press ▼ / ▲ button to select Auto Scan, then press Enter / ►button to enter sub-menu.

               Tuner type is Antenna                                                                Tuner type is Cable

 

Country
Press ◄ / ► button to select country

Mode
Press ◄ / ► button to select Mode: DTV+ATV, DTV, ATV.

Scan Type
Press ◄ / ► button to select Scan Type: Advanced, Quick, Full.

Network ID
Press ◄ / ► button to select Network ID: Auto or enter digital numbers.

Frequency
Press ◄ / ► button to select Frequency: Auto or enter digital numbers.

Symbol Rate
Press ◄ / ► button to select Symbol Rate:Auto or enter digital numbers.

Start
Press Enter / ► button to start the auto searching.
It will search digital channels first, then analog channels.
Before execute auto channel search, please confirm your antenna type is Antenna or Cable.
Wrong setting of Signal Type maybe cause finding no channel.

Manual Scan
Search for the channels manually.
Press ▼ / ▲ button to select Manual Scan, then press Enter / ► button to enter sub-menu.

Digital Manual Scan
Press ▼ / ▲ button to select Digital Manual Scan, then press Enter / ►button to enter sub-menu.

Tuner type is Antenna                                                                            Tuner type is Cable                 

Network ID
Press ◄ / ► button to select Network ID: Auto or enter digital numbers.

Frequency
Press ◄ / ► button to select Frequency: Auto or enter digital numbers.

Symbol Rate
Press ◄ / ► button to select Symbol Rate: Auto or enter digital numbers.

Modulation
Press ◄ / ► button to select Modulation: Auto, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM.

Start
Press Enter / ►button to start the channel searching.

Analog Manual Scan
Press ▼ / ▲ button to select Analog Manual Scan, then press Enter / ► button to enter sub-menu.

Analog Scan
Press ◄ / ► button to select Analog Scan.

Channel to Save
Press ◄ / ► button to select Channel to Save.

Color System
Press ◄ / ► button to select Color System: Auto, PAL or SECAM.

Sound System
Press ◄ / ► button to select Sound System: Auto, DK, BG, I or L.

AFC (Auto Frequency Control)
press◄ / ► button to select On or Off.

Start
Press Enter / ► button to start the channel searching.

Channel Edit

Press ▼ / ▲ button to select Channel Edit, then press Enter / ► button to enter sub-menu.

 The three colored key are the shortcut key for programming the channels.
First press ▼ / ▲ to highlight the channel you want to delete or move or skip, then:
Press the  button to delete the channel.
Press the button to skip the select channel.
(Your TV set will skip the channel automatically when using CH+/- to view the channels.)
Press the button to to set the channel to moving state. then press ▼ / ▲ to move
it to the position you want to put,and press button again to done the move operation.

Common interface
Press ▼ / ▲ button to select Common interface, then press Enter button to enter sub-menu.
Only available when there is CI card under DTV.

            

Signal Information
Press ▼ / ▲ button to select Signal Information, then press the Enter button to see the detail information about the signal. Only available when there is signal under DTV.

Lock System Menu

Press MENU button to display the main menu.
Press ◄ / ► button select LOCK SYSTEM in the main menu, then press ENTER / ▼ to enter.

1. Press ▼ / ▲ button to select the option that you want to adjust in the LOCK SYSTEM menu.
2. Press Enter/◄ / ► button to adjust.
3. After finishing your adjustment, Press MENU button to return back to the previous menu.

Default password is 0000, and if forget what you set, please call the service center.

Enable

Press ▼ / ▲ button to select Enable, then press◄ / ► button to select On or Off.
Channel Locks, Parental Rating and Lock Keypad are available when Enable is On.
Channel Locks
Press ▼ / ▲ button to select Channel Locks, then press Enter / ► button to enter sub-menu.

Parental Rating
Press ▼ / ▲ button to select Parental Rating, then press◄ / ► button to select.

Lock Keypad
Set to prevent it from being used by young children, or other unexpected usage.
Press ▼ / ▲ button to select Lock Keypad, then press ◄ / ► button to select On or Off.

New Password
Press ▼ / ▲ button to select New Password, then enter a 4-digital number you want to set twice.

Clear Lock
Press ▼ / ▲ button to select Clear Lock.

Setup Menu

Press MENU button to display the main menu.
Press ◄ / ► button select SETUP in the main menu, then press ENTER / ▼ to enter.

1. Press ▼ / ▲ button to select the option that you want to adjust in the SETUP menu.
2. Press Enter/◄ / ► button to adjust.
3. After finishing your adjustment, Press MENU button to save and return back to the previous menu.

OSD Language

Select an OSD menu language can be displayed.Default English is selected as menu language.

Press ▼ / ▲ button to select OSD Language, then press◄ / ► button to select.

Audio Languages
Select an audio language can be displayed.Default English is selected as audio language.
Press ▼ / ▲ button to select Audio Languages, then press Enter button to enter sub-menu.
Press ▼ / ▲ / ◄ / ► button to select the Audio Primary Language and Audio Secondary Language.

Subtitle
Select a subtitle language can be displayed.Default English is selected as subtitle language.
Press ▼ / ▲ button to select Subtitle, then press Enter button to enter sub-menu.

Mode
Press ▼ / ▲ button to select Mode then press, ◄ / ► button to select On or Off.
Press ▼ / ▲ / ◄ / ► button to select the Subtitle Primary Language and Subtitle Secondary Language.

Hearing Impaired
Press ▼ / ▲ button to select Hearing Impaired, then press ◄ / ► button to select On or Off.

Teletext
Adjust Teletext settings. Only available under DTV, ATV, AV, SV and SCART source.
Press ▼ / ▲ button to select Teletext, then press Enter / ►button to enter sub-menu.

Under DTV source, press ◄ / ► button to select Digital Teletext Language and Decoding Page Language.
Under ATV,AV, SV and SCART source ,press ◄ / ► button to select Decoding Page Language.

Mode Setting
Press ▼ / ▲ button to select Mode Setting.

Time Settings
Press ▼ / ▲ button to select Time Settings, then press Enter / ► button to enter sub-menu.

OSD Time
Press ▼ / ▲ button to select OSD Time, press ◄ / ► button to select.

(Available OSD Time:Off,10seconds,20seconds,30seconds,60seconds).

Sleep Timer
Set a timer for the TV to turn off automatically.
Press ▼ / ▲ button to select Sleep Timer, press ◄ / ► button to select.
(Available Sleep Timer:Off ,5mins, 15mins, 30mins, 60mins, 90mins, 120mins, 240mins).
Select your time zone.

Auto Sleep
Press ▼ / ▲ button to select Auto Sleep, press ◄ / ► button to select Off, 3 hours, 4 hours or 5 hours.

Time Zone

Select your time zone.
Press ▼ / ▲ button to select then press Enter / ►button to enter sub-menu.

Time
Press ▼ / ▲ button to select Time, then press Enter / ►button to enter sub-menu.
Set Auto Sync to Off,then you can set the time manually .
Note: In the case of loss of power, the clock setting will be lost.

PVR Settings
Press ▼ / ▲ button to select PVR Settings, then press Enter button to enter sub-menu.
It will check the USB.

Press ◄ / ► button to select File Manager, then press Enter button to enter sub-menu.

Press ◄ / ► button to select Device List, then press Enter button to enter sub-menu.

Press ◄ / ► button to select Scheduled Record, then press Enter button to enter sub-menu.

First Time Setup
Press ▼ / ▲ button to select First time Setup, then press button Enter to enter.

Reset
Press ▼ / ▲ button to select Reset, then press Enter button to enter sub-menu.
If you are sure to reset, press Yes to reset.

EPG Menu

Press the button EPG in the remote control to enter EPG menu.

Press the  button to display previous date.
Press the  button to display next date.
Press the  button to see the setting you have done before.
Press the  button to set the time you want to remind the program you want to see.

Timeshift
Press Pause key when the program is playing under the DTV Source to start Timeshift.

The white bar indicated the recording progress.
The blue bar indicated the playback progress.

PC

PC Setting Menu

Press INPUT button on the remote control to select PC.
Press MENU button on the remote control to display the main menu.
Press ◄ / ► button on the remote control to select PC SETTING in the main menu.

1. Press ▼ / ▲ button on the remote control to select the option that you want to adjust in the PC SETTING menu.
2. Press Enter button on the remote control to adjust.
3. After finishing your adjustment, Press MENU button to return back to the previous menu.

Auto Adjust
Press Enter/ ►button to adjust the screen automatically to the optimal position of the picture.

H Position
Adjust the horizontal position of the picture.H Position.

V Position
Adjust the vertical position of the picture.

Phase
Adjust the horizontal interfering lines.

Clock
Adjust the vertical interfering lines.

Notes:   1. Sharpness,Saturation and Advanced Settings in PICTURE menu are invalid.   2. Audio Description and Sound Type in SOUND menu are invalid.   3. Channel Locks and Parental Rating in LOCK menu is invalid.   4. Audio Languages, Subtitle,Teletext and PVR Settings in SETUP menu is invalid.   5. PC mode has no CHANNEL menu.

 

USB

USB OPERATION

Note: Before operating USB menu,Plug in USB device, then press INPUT button to set the Input Source to USB.
Press ◄ / ► button to select USB in the Source menu, then press Enter button to enter.

Press ◄ / ► button to select the option you want to adjust in the main USB menu, then press Enter button to enter.

Photo
Press ◄ / ► button to select PHOTO in the main menu, then press Enter button to enter.
Press ▼ / ▲ button to select drive disk you want to watch, then press Enter button to enter.
Press ▼ / ▲ button to select return option to back to the previous menu.

Music

Press ◄ / ► button to select MUSIC in the main menu, then press Enter button to enter.
Press ▼ / ▲ button to select drive disk you want to watch, then press Enter button to enter.
Press ▼ / ▲ button to select return option to back to the previous menu.

When highlighting the option you select, the file information will appear on the right.

   Press to play or pause.
   Press to play the previous song.
   Press to play the next song.
  Press to play backward.
  Press to play faster.
  Press to stop.

Press CH+/- to switch operation focus between File List and Player.

Movie

Press ◄ / ► button to select MOVIE in the main menu, then press Enter button to enter.
Press ▼ / ▲ button to select drive disk you want to watch, then press Enter button to enter.
Press ▼ / ▲ button to select return option to back to the previous menu.

   Press to play or pause.
   Press to play the previous movie.
   Press to play the next movie.
  Press to play backward.
  Press to play faster.
  Press to stop and back to the previous folder.

Text

Press ◄ / ► button to select TEXT in the main menu, then press Enter button to enter.
Press ▼ / ▲ button to select drive disk you want to watch, then press Enter button to enter.
Press ▼ / ▲ button to select return option to back to the previous menu.

When highlighting the option you select, the file information will appear on the right.

Troubleshooting 

No Power	Check the AC cord of TV is plus in or not. If still no power, please Pull out the plug and re-plug in after 60 seconds. And open the TV again
Signal receive not properly	To cause double image or phantom if there has high building or high mountain round TV. You can adjust image effect by manually operation: consult instruction of vernier regulation or change the direction of external antenna. If you use the indoor antenna under certain circumstance, receive will be more difficult. So you can change the direction of the antenna to adjust the image effect. If can't change image receiving effect either, you have to use external antenna.
No picture	Check the antenna at the back of TV is connected properly or not. Try to select other channels and check whether the TV problem itself or not.
But, Video is okay without audio	Increase the volume. Check the TV is in mute mode or not, and please press the mute button to make sound resume.
Audio is okay, but color error or no picture.	Increase contrast and brightness.
Snow statics picture and noise	Check the antenna at the back of TV is connected or not.
Level broken line	Vacuum, such as hairdryer, Maybe has electrical appliance interfere- please turn off these kinds of electrical appliance, cleaner and so on.
Image or-Dual "simulacrum" The TV no response with the Remote.	Perhaps the location for the antenna is not good. Use the tall beamed antenna can be improved quality of the display image. Operate the remote direct to the remote sensor on the TV. If still no response for the TV, please check if the plastic bag on the remote take or not. And check if the location for the battery is correct. Change the new battery. The TV will shift to the STAND BY if no response from the remote in the few minutes.
NO Video In (PC Mode)	Please check if the display cable connects to the VGA correct. Please check if there has the bend on the display cable.
Vertical twinkling (PC Mode)	Enter the main menu, Use the clock regulator for the Video display noise to eliminate the vertical line.
Horizontal ripping (PC Mode)	Adjust the Audio sound horizontal in the main menu to clear the horizontal ripping line.
The screen is too bright or too dark (PC Mode)	Adjust the contrast ratio or brightness in the main menu.
PC Function no response	Check the computer setting in the state of compatible display resolution.
Ripping line in RCA connecting	Please use good quality connecting cable.
Problem still exist	Unplug the power cable and wait for 30 seconds, then connect. If there is some problem with our TV, do not repair it by yourself, please contact with the customer service center.