Safety & Warnings
|
Handle with care and inspect regularly to ensure product is in good working order. If this product, power supply cord or plug shows any signs of damage: stop use, unplug the product and contact Kogan.com support. |
- Read all instructions before using the appliance and retain for reference.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- This appliance is designed for consumer use: follow directions and use only as described.
- Do not use with an extension cord unless necessary, and if so, ensure it is suitably rated and it is handled safely as is the product's own power cord:
- Do not allow the power cord to be exposed to water, heat, direct sunlight or overhang where it can be pulled or otherwise be damaged or pose a hazard.
- Unplug the monitor before cleaning it with a slightly damp, soft cloth.
- Wiping the screen with a dry cloth is recommended, only once the screen has been turned off.
- Do not use cleaning alcohol or ammonia-based liquids.
- This monitor is designed with ventilation holes on the back of the cabinet. Do not cover them or block them.
- Avoid placing the monitor near heaters, stoves, fireplaces or other sources of heat, as well as in rooms lacking in adequate ventilation.
- Do not insert any objects or spray liquids into the vents.
- Please do not position the monitor in unsafe locations. If the monitor falls, it may be damaged and may hurt nearby people.
- Unplug the monitor if it is not going to be in use for an extended period of time.
- Please do not put heavy items on the monitor or on its cord.
- Do not open the monitor back panel, as the monitor contains high voltage current, even when not plugged into a power source.
- This appliance contains no user-serviceable parts. If it suffers any failure or damage, cease usage and contact Kogan Support after consulting the Troubleshooting section of this manual.
Overview
Setup
- Insert a DisplayPort cable or HDMI cable into the output on your PC.
- Connect the power cable to AC power supply and the monitor power input.
- Turn on the power source supply.
- Press the power button to turn on the monitor.
Stand Installation
- Place the monitor face down on a soft cloth or cushioned surface.
- Install the stand base to the monitor.
- Use only recommended screw size for wall or desktop mounts to avoid damaging the screen.
Control Buttons
The back right side of the monitor has joystick control button that is utilised for accessing the monitor settings with aid of the On-Screen Display (OSD).
|
|
JOYSTICK UP: Display main menu / Confirm selection |
|
|
JOYSTICK DOWN: Exit OSD menu / When not in OSD, change input |
|
|
JOYSTICK LEFT: Decrease sound / Adjust OSD |
|
|
JOYSTICK RIGHT: Increase sound / Adjust OSD |
|
|
JOYSTICK PRESS: Power on/off |
OSD Menu
Press UP and the main OSD (On-Screen Display) menu will appear as below.
Press LEFT/RIGHT to select PICTURE in the main menu, then press UP to enter.
Picture Settings
Brightness
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Contrast
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Sharpness
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Aspect Ratio
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to set the desired aspect ratio and UP to accept.
Ultra Vivid
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to select Off, High, Low or Middle and UP to accept.
DCR
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to select ON or OFF and UP to accept.
Colour Menu
Colour Effect
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to select Standard, Game, Movie, Photo or Vivid and UP to accept.
Saturation
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Gamma
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Temperature
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
R / G / B
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to select adjust individual Red, Green and Blue colour values and UP to accept.
Advanced Menu
Volume
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to adjust and UP to accept.
Mute
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to set on/off and UP to accept.
Over Drive
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to set on/off and UP to accept.
Adaptive Sync
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to set on/off and UP to accept.
Low Blue Ray
Press LEFT/RIGHT to select and UP to confirm. Then press LEFT/RIGHT to set Low, Middle or High and UP to accept.
OSD Settings
- Language
- Time
- H+V position
- Transparency
- Reset